2023年12月3日发(作者：)

304-Keyboard or System Unit Erroraudible beeps: none

0 possible cause: keyboard, keyboard cable, mouse controller, or system board failure.

action:

1. be sure the keyboard and mouse are connected.

only authorized technicians trained by hp should attempt to remove the system board. if you

believe the system board requires replacement, contact hp technical support before proceeding.

2. run insight diagnostics ("hp insight diagnostics" on page 101) and replace failed components

as indicated.

400 series

list of messages:

40x-parallel port x address assignment conflict

404-parallel port address conflict detected

40x-parallel port x address assignment conflict

audible beeps: 2 short

possible cause: both external and internal ports are assigned to parallel port x.

action: run the server setup utility and correct the configuration.

404-parallel port address

...a hardware conflict in your system is keeping some system components from working

correctly. if you have recently added new hardware remove it to see if it is the cause of the conflict.

alternatively, use computer setup or your operating system to insure that no conflicts exist.

audible beeps: 2 short

possible cause: a hardware conflict in the system is preventing the parallel port from working

correctly.

action:

1. if you have recently added new hardware, remove it to see if the hardware is the cause of the

conflict.

the server setup utility to reassign resources for the parallel port and manually resolve the

resource conflict.

3. run insight diagnostics ("hp insight diagnostics" on page 101) and replace failed components as indicated.

600 series

list of messages:

601-diskette controller error

602-diskette boot record error

605-diskette drive type error

611-primary floppy port address assignment conflict

612-secondary floppy port address assignment conflict

601-diskette controller error

audible beeps: none

possible cause: diskette controller circuitry failure occurred.

action:

1. be sure the diskette drive cables are connected.

2. replace the diskette drive, the cable, or both.

3. run insight diagnostics ("hp insight diagnostics" on page 101) and replace failed components

as indicated.

602-diskette boot record error

audible beeps: none

possible cause: the boot sector on the boot disk is corrupt.

action:

1. remove the diskette from the diskette drive.

2. replace the diskette in the drive.

3. reformat the diskette.

605-diskette drive type error.

audible beeps: 2 short

possible cause: mismatch in drive type occurred.

action: run the server setup utility to set the diskette drive type correctly.

611-primary floppy port address assignment conflict

audible beeps: 2 short

possible cause: a hardware conflict in the system is preventing the diskette drive from operating properly.

action:

1. run the server setup utility to configure the diskette drive port address and manually resolve

the conflict.

2. run insight diagnostics ("hp insight diagnostics" on page 101) and replace failed components

as indicated.

612-secondary floppy port address assignment conflict

audible beeps: 2 short

possible cause: a hardware conflict in the system is preventing the diskette drive from

operating properly.

action:

1. run the server setup utility to configure the diskette drive port address and manually resolve

the conflict.

2. run insight diagnostics ("hp insight diagnostics" on page 101) and replace failed components

as indicated.

1100 series

list of messages:

1151-com port 1 address assignment conflict

1151-com port 1 address assignment conflict

audible beeps: 2 short

possible cause: both external and internal serial ports are assigned to com x.

action: run the server setup utility and correct the configuration.

1600 series

list of messages:

1609 - the server may have a failed system battery. some

1610-temperature violation detected. - waiting 5 minutes for system to cool

1611-cpu zone fan assembly failure detected. either

1611-cpu zone fan assembly failure detected. single fan

1611-fan failure detected

1611-fan x failure detected (fan zone cpu) 1611-fan x failure detected (fan zone i/o)

1611-fan x not present (fan zonecpu)

1611-fan x not present (fan zone i/o)

1611- power supply zone fan assembly failure detected. either

1611-power supply zone fan assembly failure detected. single fan

1611-primary fan failure (fan zone system)

1611-redundant fan failure (fan zone system)

1612-primary power supply failure

1615-power supply configuration error

1615-power supply configuration error

1615-power supply failure, power supply unplugged, or power supply fan failure in bay x

1616-power supply configuration failure

1609 - the server may have a failed system battery.

...configuration settings may have been lost and restored to defaults. refer to server

documentation for more information. if you have just replaced the system battery, disregard this

message.

audible beeps: none

possible cause: real-time clock system battery has lost power. the system will lose its

configuration every time ac power is removed (when the system is unplugged from ac power

source) and this message displays again if a battery failure has occurred. however, the system will

function and retain configuration settings if the system is connected to the ac power source.

action: replace battery (or add external battery).

1610-temperature violation detected. - waiting 5 minutes for system to cool

audible beeps: none

possible cause: the ambient system temperature exceeded acceptable levels.

action: lower the room temperature.

1611-cpu zone fan assembly failure detected.

...the assembly is not installed or multiple fans have failed in the cpu zone.

audible beeps: none

possible cause: required fans are missing or not spinning. action:

1. check the fans to be sure they are installed and working.

2. be sure the assembly is properly connected and each fan is properly seated.

3. if the problem persists, replace the failed fans.

4. if a known working replacement fan is not spinning, replace the assembly.

1611-cpu zone fan assembly failure detected.

...failure. assembly will provide adequate cooling.

audible beeps: none

possible cause: required fan not spinning.

action: replace the failed fan to provide redundancy, if applicable.

1611-fan failure detected

audible beeps: 2 short

possible cause: required fan not installed or spinning.

action:

1. check the fans to be sure they are working.

2. be sure each fan cable is properly connected and each fan is properly seated.

3. if the problem persists, replace the failed fans.

1611-fan x failure detected (fan zone cpu)

audible beeps: 2 short

possible cause: required fan not installed or spinning.

action:

1. check the fans to be sure they are working.

2. be sure each fan cable is properly connected, if applicable, and each fan is properly seated.

3. if the problem persists, replace the failed fans.

1611-fan x failure detected (fan zone i/o)

audible beeps: 2 short

possible cause: required fan not installed or spinning.

action:

1. check the fans to be sure they are working.

2. be sure each fan cable is properly connected, if applicable, and each fan is properly seated. 3. if the problem persists, replace the failed fans.

1611-fan x not present (fan zonecpu)

audible beeps: 2 short

possible cause: required fan not installed or spinning.

action:

1. check the fans to be sure they are working.

2. be sure each fan cable is properly connected, if applicable, and each fan is properly seated.

3. if the problem persists, replace the failed fans.

1611-fan x not present (fan zone i/o)

audible beeps: 2 short

possible cause: required fan not installed or spinning.

action:

1. check the fans to be sure they are working.

2. be sure each fan cable is properly connected, if applicable, and each fan is properly seated.

3. if the problem persists, replace the failed fans.

1611- power supply zone fan assembly failure detected.

...the assembly is not installed or multiple fans have failed.

audible beeps: none

possible cause: required fans are missing or not spinning.

action:

1. check the fans to be sure they are installed and working.

2. be sure the assembly is properly connected and each fan is properly seated.

3. if the problem persists, replace the failed fans.

4. if a known working replacement fan is not spinning, replace the assembly.

1611-power supply zone fan assembly failure detected.

...failure. assembly will provide adequate cooling.

audible beeps: none

possible cause: required fan not spinning.

action: replace the failed fan to provide redundancy, if applicable.

1611-primary fan failure (fan zone system) audible beeps: none

possible cause: a required fan is not spinning.

action: replace the failed fan.

1611-redundant fan failure (fan zone system)

audible beeps: none

possible cause: a redundant fan is not spinning.

action: replace the failed fan.

1612-primary power supply failure

audible beeps: 2 short

possible cause: primary power supply has failed.

action: replace power supply.

1615-power supply configuration error

audible beeps: none

possible cause: the server configuration requires an additional power supply. a moving bar is

displayed, indicating that the system is waiting for another power supply to be installed.

action: install the additional power supply.

1615-power supply configuration error

- a working power supply must be installed in bay 1 for proper cooling.

- system halted!

audible beeps: none

possible cause: the server configuration requires an additional power supply. a moving bar is

displayed, indicating that the system is waiting for another power supply to be installed.

action: install the additional power supply.

1615-power supply failure, power supply unplugged, or power supply fan failure in bay x

audible beeps: none

possible cause: the power supply has failed, or it is installed but not connected to the system

board or ac power source.

action: reseat the power supply firmly and check the power cable or replace power supply.

1616-power supply configuration failure

-a working power supply must be installed in bay 1 for proper cooling. -system halted!

audible beeps: none

possible cause: power supply is improperly configured.

action: run the server setup utility and correct the configuration.0