2023年12月20日发(作者：)

前提条件：make_tape_recovery -A操作成功。操作步骤：1，重启系统，自检通过后在十秒中断处中断，如下所示：Firmware Version 43.43Duplex Console IO Dependent Code (IODC) revision 1------------------------------------------------------------------------------ (c) Copyright 1995-2002, Hewlett-Packard Company, Allrights reserved------------------------------------------------------------------------------ Processor Speed State CoProcessor State

Cache Size Number State Inst

Data --------- -------- --------------------- ----------------- ------------ 1 440 MHz Active Functional 512KB 1 MB 3 440 MHz Idle Functional 512KB 1 MB 5 440 MHz Idle Functional 512KB 1 MB 7 440 MHz Idle Functional 512KB 1 MB Central Bus Speed (in MHz) : 120

Available Memory : 4193284 KB Good Memory Required : 18880 KB Primary boot path: 0/0/2/1.6

Alternate boot path: 0/0/2/0.6

Console path: 0/0/4/0.0

Keyboard path: 0/0/4/0.0

WARNING: The non-destructive test bit was set, so memorywas not tested

destructively. Information only, no action required.

Processor is starting autoboot discontinue, press any key within 10 terminated.2，通过“sea IPL”命令搜索可引导设备，找到磁带机的硬件路径地址0/0/1/0.03，通过磁带机引导，过程如下：Main Menu: Enter command or menu > bo 0/0/1/0.0Interact with IPL (Y, N, or Cancel)?>

Boot IO Dependent Code (IODC) revision 1HARD Revision A.00.44 Mar 12, 2003ISL booting hpux (;0):INSTALLBoot: tape(0/0/1/0.0.0.0.0.0.0;0):WINSTALL11751424 + 1970264 + 2631464 start 0x200d68

alloc_pdc_pages: Relocating PDC from 0xffff800000 to0x7eb00000.4，加载内核成功后，有如下显示：gate64: sysvec_vaddr = 0xc0002000 for 2 pagesNOTICE: nfs3_link(): File system was registered at index : autofs_link(): File system was registered at index : cachefs_link(): File system was registered at : claimed Tachyon TL/TS Fibre Channel Mass Storage cardat 1/2/0/0 System Console is on the Built-In Serial Interface Swap device table: (start & size given in 512-byte blocks) entry 0 - auto-configured on root device; ignored - noroomWARNING: no swap device configured, so dump cannot bedefaulted to primary swap.

WARNING: No dump devices are configured. Dump ng the STREAMS daemons-phase 1Create STCP device filesStarting the STREAMS daemons-phase 2 $Revision: vmunix: vw: -proj selectors:CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' WedNov 8 19:24:56 PST 2000 $Memory Information: physical page size = 4096 bytes, logical page size = 4096bytes Physical: 4194304 Kbytes, lockable: 3203460 Kbytes,available: 3693540 Kbytes======= 06/21/07 02:21:21 EDT HP-UX InstallationInitialization. (Thu Jun 21

02:21:21 EDT 2007) @(#) Ignite-UX Revision C.6.1.44 @(#) install/init (opt) $Revision: 10.303 $ * Scanning system for * Querying disk device: 0/0/2/1.6.0 ...Recovery tape created from system: 4000new on Thu Jun 2112:51:03 2007WARNING: The configuration information calls for a non-interactive installation. Press within 10 seconds to cancelbatch-mode installation: * Using client directory:/var/opt/ignite/clients/0x00306E1345B1 * Checking configuration NOTE: Free space (4129584KB) in "/var" where/var/adm/crash is located is

less than system memory (4194304KB). This should beenough space to

capture at least a single dump (and likely more thanthat if the dump

is selective and/or compressed) in the event of asystem crash.

Additional space may be required to uncompress thedump in order to

analyze it and to save multiple dumps. You canincrease the size of

the "/var" volume on the "File System" tab when usingthe advanced

user G: The disk at: 0/0/2/1.6.0 (HP_36.4GST336752LC)appears to contain a

file system and boot area. Continuing the installationwill destroy

any existing data on this disk. Press within 10 seconds to cancelbatch-mode installation: Really cancel non-interactive install and start the user-interface? ([y]/n): y * Setting keyboard language to: PS2_DIN_US_:

The console firmware terminal type is currently set to"vt100". If you are using any other type of terminal you will see"garbage" on the

screen following this message. If this is the case, you will need to either change theterminal type

set in the firmware via GSP (if your GSP firmwareversion supports

this feature), or change your terminal emulation tomatch the

firmware. In either case you will need to restart if yourterminal and the firmware terminal type do not match.

Press the 'b' key if you want to reboot now.

Recovery tape created from system: 4000new on Thu Jun 2112:51:03 20075，通过手工中断，来到和光盘引导相同的安装界面： Welcome to the HP-UX installation/recoveryprocess! Use the key to navigate between fields, and thearrow keys within fields. Use the key to select an item. Use the or to pop-up achoices list. If the menus are not clear, select the "Help" item for moreinformation. Hardware Summary: System Model:9000/800/N4000-44 +---------------------+----------------+-------------------+ [Scan Again ] | Disks: 1 ( 33.9GB) | Floppies: 0 | LAN cards: 5 | | CD/DVDs: 0 | Tapes: 1 | Memory: 4096Mb | | Graphics Ports: 0 | IO Buses: 4 | CPUs: 4 | [H/W Details ] +---------------------+----------------+-------------------+ [ Install HP-UX ] [ Run a Recovery Shell ] [ Advanced Options ] [ Read Sys-Admin Message ] [ Reboot ] [ Help ]6，按需求进行安装即可。