2023年12月24日发(作者：)
网络连接失败（Network connection failed）
When you connect to broadband, if you make a mistake, that is,
when you cannot connect to the network, the system will provide
you with some error messages as follows: :
600 an operation is pending.
601 detected an invalid port handle.
602 specifies that the port is open.
The 603 call buffer is too small.
604 specified the wrong information.
605 cannot set port information.
606 cannot connect to the specified port.
607 detected an invalid event.
608 specifies a device that does not exist.
609 device type does not exist.
610 buffer is invalid.
611 routing is unavailable.
612 routing is not allocated.
613 specified invalid compression.
614 buffer is not enough.
615 no port found.
616 an asynchronous request is pending.
617 port or device has been disconnected.
618 port not opened.
619 cannot establish a connection to the remote computer, so
the port used for this connection is closed.
620 no endpoints.
621 cannot open phone book file.
622 cannot load phone book file.
623 cannot find phone book entry.
624 cannot write phone book file.
625 invalid information found in the phone book.
626 cannot load string.
627 cannot find key.
628 the connection is terminated by the remote computer before
the connection is complete.
The 629 data link is terminated by the remote computer.
630 port disconnected due to hardware failure.
631 the user has disconnected the port connection.
632, the structure size is not correct.
Port 633 is already in use, or no configuration ports have been
configured for remote access.
634 cannot register a computer on a remote network.
635 unknown error.
636 the wrong device is connected to the port.
637 string cannot be converted.
638 request timeout.
639 there is no asynchronous network available.
640 NetBIOS error occurred.
641, the server cannot allocate the NetBIOS resources needed
to support the client.
642 has registered a NetBIOS name on the remote network.
643, the network adapter on the server is out of order.
644 will not receive network pop-up messages.
645 internal authentication error.
646 this account is not allowed to log in at this time of day.
647 this account has been disabled.
The 648 password has expired.
The 649 account has no remote access permission.
650 remote access server did not respond.
651 modem (or other device) reported an error.
652 device response is unrecognized.
653 there is no macro necessary to find the device in the part
of the device' file.
654 the commands or responses in the file section
are referenced to undefined macros.
655 the
section.
656 the
contains undefined macros.
657 cannot open file.
The device name in the 658 device,.INF file, or file
is too long.
The 659 file references an unknown device name.
The 660 file does not contain a response to this
command.
The 661 file is missing a command.
662 attempts to set a macro that is not listed in the part of
the device' file.
The 663 file refers to an unknown device type.
664 cannot allocate memory.
The 665 port is not configured for remote access.
666 modem (or other device) does not work.
667 cannot read the file.
668 connection removed.
The usage parameter in the 669 file is invalid.
670 cannot read part of the name from the file.
671 cannot read device type from the file.
672 cannot read device names from the file.
673 can not be from the media
Read usage in INI file.
674 cannot read the maximum connection BPS rate from the
file.
675 cannot read the maximum carrier BPS rate from the
file.
676 the line is busy.
677 manual response, not modem response.
678 remote computer is not responding.
679 cannot detect carrier wave.
680 there is no dial tone.
681 common errors in device reporting.
691 deny access because the username and / or password is
invalid in the domain.
Hardware fault in 692 port or connected device.
695 not started state machine.
696 start status machine.
697 response loop not completed.
699 device response causes buffer overflow.
700 the extended command in file is too long.
701 the device moves to the BPS rate that the COM driver does
not support.
The 703 connection requires user information, but the
application does not allow the user to interact.
The 704 callback number is invalid.
705 the authorization status is invalid.
707, there are errors associated with the X.25 protocol.
708 this account has expired.
709 error modifying password in domain.
710 when communicating with the modem, a serial overload error
is detected.
711 configuration errors on this computer prevent this
connection.
The 712 Biplex port is initializing. Wait a few seconds again.
713 inactive ISDN lines are available.
714 there are not enough ISDN channels available for calling.
715 the phone line is so bad that it makes too many mistakes.
716 "remote access IP" configuration is not available.
717 there is no IP address available in the static pool of the
remote access IP address.
718 this connection has been terminated because the remote
computer has not responded in time.
719 PPP has been terminated by the remote computer.
720 cannot establish a connection to the remote computer. You
may need to change the network settings for this connection.
721 remote computer did not respond.
The 722 PPP packet is invalid.
723 the phone number (including prefix and suffix) is too long.
726 cannot simultaneously use the IPX protocol for multiple
ports to dial out.
728 could not find the IP adapter connected to the remote
access.
729 only after the IP protocol has been installed can SLIP be
used.
731 no configuration protocol.
The 732 PPP negotiation does not meet.
733 cannot complete the connection to the remote computer.
The 734 PPP link control protocol is terminated.
735 the requested address is rejected by the server.
The 736 remote computer terminated the control protocol.
Loopback was detected in 737.
738 server does not specify address.
739 the remote server cannot use an encrypted password.
740 the TAPI device configured for remote access cannot be
initialized or is not properly installed.
741 local computer does not support encryption.
742 remote server does not support encryption.
743 the remote server requires encryption.
752 syntax errors encountered when dealing with scripts.
I think this is because you streamline the system and delete
all the help files, huh?
If your network connection is no problem, this tip will
disappear naturally, no problem
发布评论