2024年5月6日发(作者：)

Protel 99SE使用指南

叙述约定 ·····························································································································4

进入Protel 4

●进入Protel ·······················································································································4

●建立新项目（File/New Design） ····················································································4

●建立新文件（File/New或Document窗口/右键New） ·················································4

●File菜单其它命令 ···········································································································4

●其它命令 ·························································································································5

通用编辑命令 5

●对象放大与缩小 ··············································································································5

●对象属性编辑 ··················································································································5

●对象选取 ·························································································································5

1.鼠标选取 ···················································································································5

2. 菜单选取（Edit/Select） ························································································6

●对象操作 ·························································································································6

1．左右键基本功能 ····································································································6

2．旋转 ·······················································································································6

3．剪贴 ·······················································································································6

4．删除 ·······················································································································6

5. 移动（Edit/Move/） ·······························································································6

5. 排列与对齐（Edit/Align/） ····················································································7

6. 撤消与重复 ·············································································································7

7. 设置原点位置 ·········································································································7

●主界面构成 ·····················································································································7

1．主菜单 ····················································································································7

2. 主工具栏与辅助工具栏 ··························································································7

3. 状态栏和命令行 ·····································································································8

4．客户机/服务器菜单 ·····························································································8

原理图编辑器 9

●基本概念 ·························································································································9

1.对象 ··························································································································9

2.网格 ··························································································································9

3.光标 ··························································································································9

●环境设置 ·························································································································9

1.启闭工具栏 (View/Toolbars) ····················································································9

2.设置（Design/Options） ···························································································9

3.增添元件库 ············································································································· 10

●元件管理器 ··················································································································· 10

1．Components （查找、选择、取用元件） ·························································· 10

1

2．Group（查找、选择、取用元件集） ·································································· 10

3．Pins（列出当前元件引脚名称及状态） ····························································· 10

4．Mode（指定元件的模式） ·················································································· 11

●绘制原理图 ··················································································································· 11

1.放置元件（Place/Part） ·························································································· 11

2.放置电源及接地符号（Place/Power Port） ···························································· 11

3.画导线（Place/Wire） ···························································································· 11

4.画总线（Place/Bus） ······························································································ 11

5.画总线端口（Place/Bus Entry） ············································································· 11

6.放置网络标号（Place/Net Lable） ········································································· 11

7.放置接点（Place/Junction） ··················································································· 12

8.放置输入输出口（Place/Port） ·············································································· 12

9.放置图纸符号（Place/Sheet Symbles） ·································································· 12

10.放置图纸入口（Place/Sheet Entries） ·································································· 12

11.放置设计指示符号（Place/Directives） ······························································· 12

12.保存文件 ··············································································································· 12

●绘制几何图 ··················································································································· 12

●生成报表 ······················································································································· 13

1．ERC报告（Tools/ERC）····················································································· 13

2.网络表（Design/Create Netlist） ············································································ 14

3.元件清单（Report/Bill of Material） ······································································ 15

4.交叉参考表（Report/Cross Reference） ································································· 15

5.网络对照表（Report/Netlist Comparison） ···························································· 15

●编辑元件库 ··················································································································· 15

1. 修改电原理图中已有的元件 ················································································ 15

2.创建新元件 ············································································································· 15

3. 创建多器件元件 ··································································································· 15

4．元件库绘图工具栏 ······························································································· 15

5.保存文件 ················································································································· 15

6.产生文件报表 ········································································································· 16

●设计技巧 ······················································································································· 16

1．绘图技巧 ·············································································································· 16

2．PCB设计对原理图设计的要求 ··········································································· 16

3．其它技巧 ·············································································································· 16

●打印 ······························································································································· 16

增加模块 ··························································································································· 17

PCB编辑器 21

●基本概念 ······················································································································· 21

1．基本概念 ·············································································································· 21

2．单位换算 ·············································································································· 21

3．一般步骤 ·············································································································· 21

●环境设置 ······················································································································· 21

1.启闭工具栏 (View/Toolbars) ·················································································· 21

2.层的设置 ················································································································· 21

2