2024年5月10日发(作者：)

日成尼龙扎线带系列

Nylon Cable Tie

日成尼龙扎线带的储存与使用　

RCCN尼龙扎线带是以进口高品质尼龙６６原料所制造而成。尼龙原料的特性是具　吸湿性　也易　释出水份　，所以尼龙扎线带需加水处理并密封在塑胶袋，使品质维持在最适当状态。因此，如何保存密封的扎线带是非常重要的。

（一）保存扎线带的理想环境，温度约在２３℃。湿度在５０％以上。（二）未使用扎线带前，请勿开封，一旦开封也请尽量在短时间内使用完毕。如果未能在短时间内用完一包的数量请务必封包。

（三）不要将扎线带直接暴晒在太阳底下，否则，建议使用耐候性的扎线带。　　　　　　　　　　　

　避免靠近　加热器、暖气等产品或设备捆扎需求高低温环境应选用相对应性能的扎带。

RCCN nylon cable tie is made of high quality nylon 66,material nylon is hygroscopicity,and easy to disengage wet，for that, cable tie should be stored in wet bags and sealed,keep it in suitable enviroment.

1, The suitable environment for storing cable tie,temperature 23℃,moisture rate should above 50%

2, Don’t open if you no need to use it,once the bag is opened, cable ties should be used in short time,seal it, after using

3, Don’t put the cable tie outdoor and under the sun,or else，please choose UV resistant cable tie

In voide close to heating quipments

ISO9001

RoHSREACH

RCCN

RCCN

日成尼龙扎线带特点

Cable Tie Features/Benefits:

独特的构造

One Piece Construction

平滑的边角

Smooth, Round Edges

拉伸的强度

Tensile Strength

．　可靠性、稳定性佳

．　长度从2.8”(71mm)到43.3”(1100mm)

　　适用于不同设备和环境的需求

• Consistent performance and reliability

• Available in lengths from 2.8" (71mm) up to

43.3" (1100mm) to meet a variety of

application requirements

．　不会伤到安装者的手，提高产能

．　防止损坏电线的绝缘层

• No irritation to installer’s hands, increases

productivity

• Prevents damage to wire insulation

．　超过航天航空行业标准(AS23190)

．　有７种不同的拉伸强度从8lbs.(36n).8KG

　　到250lbs(1112N).114KG,提供经济的选择。

• Exceeds Industry and Aerospace Standards

SAE (AS23190) standards

• Available in seven loop tensile strengths from

8 lbs. (36N).8KG up to 250 lbs. (1112N).114KG

to provide an economical selection

日

成

尼

龙

扎

线

带

特

点

Cable Tie Features/Benefits:

弯曲的尖部

Curved Tip

末梢的防滑线

Fingger Tip Grip

每英寸更多的齿

More Teeth Per In ch

．　尖部弯向头部，提高安装速度—降低安装成本

．　较快的初始绕线

．　平地上面更易捡起

• Orients tip toward head to speed installation

— lowers installed cost

• Faster initial threading

• Easier to pick up from flat surfaces

．　可以选择有末梢倒戈的尺寸确保带部顺利导入

．　倒戈设计可以捆绑时防止扎带从头部滑出

• Finger tip grip on selected sizes assures

positive grip during threading of the tie

• Grip prevents tip from slipping out of cable

tie head during threading

．更多数量独特的齿为更紧的捆绑提供保证

．由于平滑的表面，可以提供适当的电线捆绑而

不损坏电线绝缘层

• Greater number of small uniform teeth

provides tighter bundles

• Because they are flush with surface they

provide proper wire bundle grip without wire

insulation damage

捆绑用力小

Low Threading Force

每根的锁头设计

One Piece Locking Design

不同材质的扎带

Material Availability

．　任何一根扎带捆绑时都是行业内最省力的

．　节省作业人员的体力

．　薄尖型的设计更易于插入、捆绑

• Lowest threading force of any one piece cable

tie in the industry

• Reduces operator fatigue

• Thin tapered tip facilitates threading, easier

initial insertion

．　数量较多的锁齿设计，提供更高的拉伸强度

　　和可靠性

．　自锁式和可退式扎带两种不同的设计应用于

　不同场合的需求

• Multiple locking tooth design provides greater

strength and reliability

• Available in self locking or releasable styles

for use in applications where changes are

anticipated

．　具有多种不同材质的扎带，应用于不同的环境

．　根据使用环境的不同，适当选择室内或者室外

　　使用的扎带，确保性能的持久性

• Available in a variety of materials to meet the

needs of special environments

• Properly selected ties can be used indoors or

outdoors with assurance of long lasting

performance

B1