2023年12月13日发(作者：)
开机启动出现press f1 to resume要按f1才能进（Boot up appear
press F1 to resume, press F1 to enter）
开机启动出现按F1继续要按F1才能进
我想你是不是在BIOS中设置了开机检测软驱，而你又没有装软驱。你在BIOS的高级BIOS功能中将启动软盘寻求设置为试试电脑启动的时候要按下F1才可以进系统残疾人。
开机按F1键，这是因为你的BIOS设置不当但也能正常引导系统，属非致命性故障，按F1是在问你是否继续。
把开机/开机设置配置/“如果错误等F1”项改为禁用。
你没有安装软盘驱动器，但是在CMOS中设置了，开启软驱的选项。
方法是：开机按del键，进入BIOS设置，选择第一个”基本设置”，把软一项设置没”disabel”无效就可以了。
2刚开始开机时按del进入BIOS，按回车键进入第一项，看看里面的“驱动”项是不是“无”，不是的话按“PgUp”或“PgUp”进行修改，修改后按“ESC”退出，选”保存设置退出“项按回车退出BIOS，重启，再不行的话就换了电池再按上面的步骤重新设置既可。
3开机需要按下F1键才能进入，主要是因为BIOS中设置与真实硬件数据不符引起的，可以分为以下几种情况：
1、实际上没有软驱或者软驱坏了，而BIOS里却设置有软驱，这样就导致了要按F1才能继续。
2、原来挂了两个硬盘，在BIOS中设置成了双硬盘，后来拿掉其中一个的时候却忘记将BIOS设置改回来，也会出现这个问题。
3、主板电池没有电了也会造成数据丢失从而出现这个故障。
4、重新启动系统，进入BIOS设置中，发现软驱设置为1.44m了，但实际上机箱内并无软驱，将此项设置为没有后，故障排除。
曾经有很多人问过这样的问题，下面将我遇过的此类问题做一下总结，希望对大家有所帮助。
1、监视功能发现错误，进入电源管理设置查看详细资料，按F1键继续，按DEL键进入设置
中文：监视功能发现错误，进入电源管理设置察看详细资料，按F1键继续开机程序，按del键进入COMS设置。
解释：有的主板具备硬件的监视功能，可以设定主板与CPU的温度监视、电压调整器的电压输出准位监视和对各个风扇转速的监视，当
上述监视功能在开机时发觉有异常情况，那么便会出现上述这段话，这时可以进入COMS设置选择电源管理设置，在右面的* * * * * *、风机监测监控和热** ** **察看是哪部分发出了异常电压监控，然后再加以解决。
2、PRI从动ATAPI lncompatible按F1继续
可能是你的光驱没接好或有故障，最好在CMOS中将各IDE口设为自动。
3、按F1继续，德尔进入安装程序
开机后按del进入BIOS，在选择软驱中选择没有后按F10保存就可以了
4、CMOS校验和错误－默认加载
按F1继续吗？进入安装程序
08／09／2000－i810－ite8712－6a69me1cc－00
CMOS电池没电。
5，警告！CPU已更改！请输入CPU速度CMOS设置，并记得退出前保存！
这说明BIOS设置被冲掉了，
To reset the BIOS (also known as the CMOS setting). Turn on the
"Del" button, enter the settings, and see your motherboard
manual. What is your CPU frequency? In the BIOS to select the
frequency locking of the FSB, anyway. 66, 100 or 133 FSB always,
to see the CPU model, from low to high settings. If it is the
BIOS settings of AWARD, select Frequency/Voltage Control
(frequency / voltage control) on the home page, and use this
menu to set the frequency and voltage in particular. Among them,
"Clock By Slight Adjust (clock frequency fine-tuning)" allows
you to select the CPU clock frequency. Various motherboard BIOS
settings are different, you can refer to your motherboard
manual to adjust.
CPU, has, been, changed, please, re-enter, CPU, settings, in,
the, CMOS, setup, and,, remember, to,, save, before, quit! Some have a FSB jumper on the motherboard, the default is 100MHZ,
some motherboard does not support automatic frequency. As long
as you get into the BIOS FSB set FSB CPU standard you can, the
general frequency is set automatically, it is best not to
overclock
Why do you press F1 to enter the system? This question is too
much:
If your computer starts, you must press the F1 button to get
into the system. This is because your BIOS is improperly
configured, but you can also boot the system normally. It's a
non fatal fault. Press F1 to ask if you want to continue.
The solution to boot is to press F1:
A: press the Del button, enter the BIOS settings, select the
first "basic settings", the "floopy" set a "Disabel" is invalid
Two: the first boot press DEL to enter BIOS, press the Enter
key to enter the first, look at the inside of the "Drive A" is
not "None", is not the case according to the "Pgup" or "PgDn"
modified, amended according to the "ESC" exit, "Save & Exit
Setup" item and press enter exit BIOS, then restart, if not
change the battery according to the above steps can be re set.
Three: boot need to press the F1 key to enter, mainly because
the BIOS settings and real hardware data inconsistent, can be
divided into the following circumstances:
1, in fact, no floppy or floppy drive is broken, and the BIOS
is provided with a floppy drive, which causes the press F1 to
continue.
2, originally hung two hard disk, in the BIOS set into a double
hard disk, and then remove one of them, but forget to change
the BIOS settings, there will be this problem.
3, the motherboard battery is not power, it will cause data loss,
resulting in this fault.
4, restart the system, enter the BIOS settings, and found that
the floppy drive is set to 1.44M, but in fact there is no floppy
drive in the chassis, the set to NONE, troubleshooting.
=====================================================================================
Once a lot of people have asked such a question, the following
to sum up such problems, we hope to help.
Hareware, Monitor, found, an, error, enter, POWER, MANAGEMENT,
SETUP, for, details, Press, F1, to, continue, DEL, to, enter,,
SETUP
English: monitor function to detect errors, enter POWER
MANAGEMENT SETUP, view details, press F1 to continue the boot
program, press DEL to enter the COMS settings.
Interpretation: some motherboards have the hardware monitoring
function, you can set the motherboard and CPU temperature monitoring, voltage regulator output voltage monitoring and
monitoring the speed of each fan, when
The monitoring function at boot time found abnormal situation,
then there will be above this, then you can set into the COMS
POWER MANAGEMENT SETUP, Monitor**, **Thermal in the right side
of the **Fan Monitor** and **Voltage Monitor** to see which part
of a anomaly, and then solve them.
2、PRI从动ATAPI lncompatible按F1继续
可能是你的光驱没接好或有故障，最好在CMOS中将各IDE口设为自动。
3、按F1继续，德尔进入安装程序
开机后按del进入BIOS，在选择软驱中选择没有后按F10保存就可以了
4、CMOS校验和错误－默认加载
按F1继续吗？进入安装程序
08／09／2000－i810－ite8712－6a69me1cc－00
CMOS电池没电。
5，警告！CPU已更改！请输入CPU速度CMOS设置，并记得退出前保存！
这说明BIOS设置被冲掉了，要重新设置BIOS（又叫做CMOS设置）。开机按住“DEL”键进入设置，看你的主板说明书。你的CPU频率是多少？在BIOS中要选好外频，倍频反正是锁定的。外频总是66、100或133，要看CPU型号，从低往高设置。如果是奖的BIOS设置，在首页就选频率/电压控制（频率/电压的控制），使用此菜单可以对频率、电压进行特别的设定其中”。时钟由Slight Adjust（时钟频率微调）”允许你选择CPU时钟频率。各种主板的BIOS设置有差别，可以参考自己的主板说明书进行调整。
6、CPU已更改，请重新输入CMOS设置中的CPU设置，并记得在退出前保存！
有些主板上有个外频跳线，默认为100MHz，还有些主板不支持自动调频。你只要进BIOS里把外频设置成你的CPU标准外频就可以了，倍频方面一般是自动设置，最好不要超频。
如果上述解决办法都不能解决的话，你可以检查CMOS旁边电路是否有烧坏的迹象，我的机器就是因为CMOS旁边的电路有问题，上述机决方法都试过了也没用，最后一烙铁就搞定呵呵，不妨你也试试！
=====================================================================================
开机需要按F1才能进入系统的故障排除
在通常情况下，要求按F1进入系统都是系统的BIOS设置有不影响系统启动的小问题所致，所以请检查BIOS里的硬件信息设置与实际不符之处。
一般常见故障是：
1、主板上的电池没电了。 解决方法：换主板电池。
2、你设置了软驱启动，但是你的软驱有问题。
解决方法：
一个、开机按del进入BIOS，开机启动顺序，关闭软驱启动。
B、关闭开机软驱检测功能：
启动电脑，然后按【del】键进入BIOS设置主界面；
选择“高级BIOS功能”设置项，按回车键进入；
将”启动软盘寻求“设置为“禁用”，这样即可关闭开机软件检测功能了。
=====================================================================================
开机按F1才能进入（启动）系统的解决方案
1、BIOS检查和错误，系统停止
（BIOS信息进行总和校验时发现错误，系统锁定）
解决方案：这个错误是一般人不会遇到的，这种信息多半是对主板BIOS刷新不完整才会出现的，惟一的处理方式就是重新刷新BIOS，但不能保证一定成功。
2、CMOS电池失效
（CMOS电池失效）
解决方案：这说明CMOS电池已经没电了，只要将主板上的钮扣电池取下，
Change a new battery. Most motherboards use 3V's button
batteries, so don't buy 5V batteries! As long as you look at
the surface of the battery carefully, you can clearly see the
word "3V" on it.
3, CMOS, check, sum, error-Defaults, loaded
(CMOS finds errors when performing full checking and loads
system defaults)
Solution: this situation is usually caused by a lack of battery
power. It is recommended to replace the battery first. If the
problem is still not resolved, so that CMOS RAM and CMOS RAM
may issue, because our person is unable to repair, if the dealer
handles the motherboard is still under warranty please contact
the motherboard manufacturer or to buy.
4, Display, switch, is, set, incorrectly
(display switch configuration error)
Solution: as long as your motherboard is not old, this
information will certainly not appear. In general, there is a
route on the old motherboard to set the screen to monochrome or color. This information indicates that the settings on the
motherboard are inconsistent with the CMOS settings, so just
judge who is correct for the motherboard and the CMOS settings,
and then update the wrong settings.
5, Floppy, disk (s), fail or Floppy, disk (s), fail (80) or
Floppy, disk (s), fail (40)
(floppy drive failed)
Solution: check that the floppy drive's data line is properly
connected to see if there is any reverse or loose connection.
Don't tell me, the plug is not connected! If you do not have
a floppy drive, it is recommended to set "Drive A" to "None"
in the CMOS Setup program". I'd like to find a good floppy to
try it on. To verify that the original floppy drive is out of
order.
6, Hard, disk (s), diagnosis, fail
An error occurred while performing the hard disk diagnostics
Solution: this information appears, in general, that the hard
disk itself is out of order. You can try hard disk to another
computer. If the problem is not solved, it could be a serious
physical failure on this hard disk.
7, Hard, disk (s), install, failure
(hard disk installation failed)
Solution: check whether the power line or data line of the hard
disk is properly connected. If the jumper with a IDE line to
connect two IDE device settings are the same, as long as the
jumper these two IDE devices can be set different (generally
will be the main hard disk is Master, another is Slave).
8, Hard, disk (s), initializing (Please, wait, a, moment)... )
(initializing hard disk, please wait a moment)
Solution: this information is not visible on newer disks, but
on older disks, this information is seen because it is slower.
Hardware, Monitor, found, an, error, enter, POWER, MANAGEMENT,
SETUP, for, datails, Press, F1, to, continue, DEL, to, enter,,
SETUP
(monitor function to detect errors, enter POWER MANAGEMENT
SETUP, view details, press F1 to continue the boot program,
press DEL to enter the CMOS settings)
Solution: some motherboards have the monitoring function of the
hardware, the output voltage can be set with the CPU motherboard
temperature monitoring, voltage regulator monitoring and
monitoring of various quasi fan speed, when the monitoring
function at boot time found abnormal situation will appear this
information, then you can enter the CMOS settings, see "POWER
MANAGEMENT SETUP" what is abnormal, and then to be addressed.
10, Keyboard, error, or, no, keyboard, present
(keyboard error or missed keyboard)
Solution: check if the keyboard's connection is loose or
damaged, and some of the lower quality keyboards are prone to
this information.
11, Memory, test, fail
(memory check failed)
Solution: This is usually due to memory failure or failure. It
is recommended that you plug the memory bar again, perhaps
because the memory is not compatible with each other.
To each boot a memory the batch test, to find out the fault
memory, it can be repaired or removed.
12, Override, enable-Defaults, loaded
(the current CMOS setting cannot start the system and load the
default values in the BIOS to start the system.)
Solution: in general is set within the CMOS setting error will
appear this information, as long as to enter the CMOS settings
and select "Load Setup Defaults" into the set value of the
original system, and then restart.
13, Press, TAB, show, POST, screen
(press TAB to toggle screen display)
Solution: some motherboard manufacturers will to design their
own boot screen to replace the default BIOS boot screen, and
this information is to tell the user can press the "TAB" key
to manufacturers to design their own boot boot screen display
and BIOS display screen to switch the default.
14, Press, ESC, to, skip, memory, test
(memory check is in progress. Press ESC to skip)
Solution: of course, you can press ESC to end the memory test,
or wait for the test to pass. If you don't want to wait, go to
the CMOS settings and select "BIOS Features Setup", which will
be the "Quick Power On Self Test" set to "Enabled", stored after
restarting.
Primary, master, hard, fail, or Primary, slave, hard, fail, or
Secondary, master, hard, fail, or Secondary slave hard fail
(failed to detect hard disk)
Solution: CMOS settings may be inappropriate, for example not
from the disk but in CMOS settings set to have from the disk,
then the error will appear, then you can enter the CMOS settings
for the automatic detection of the hard disk, may also be the
power line of the hard disk, the data line may be missed or
improper hard drive jumper settings.
Resuming, from, disk, Press, TAB, to,, show, POST, screen
Boot from the hard disk, press TAB to show the boot screen Solution: This is because some of the motherboard BIOS provides
Suspend to disk (hard disk hanging) "function, if we use Suspend
to disk to shut down, then we will be in the next boot display
this message. Why do you press F1 to enter the system? This
question is too much:
If your computer starts, you must press the F1 button to get
into the system. This is because your BIOS is improperly
configured, but you can also boot the system normally. It's a
non fatal fault. Press F1 to ask if you want to continue.
The solution to boot is to press F1:
A: press the Del button, enter the BIOS settings, select the
first "basic settings", the "floopy" set a "Disabel" is invalid
Two: the first boot press DEL to enter BIOS, press the Enter
key to enter the first, look at the inside of the "Drive A" is
not "None", is not the case according to the "Pgup" or "PgDn"
modified, amended according to the "ESC" exit, "Save & Exit
Setup" item and press enter exit BIOS, then restart, if not
change the battery according to the above steps can be re set.
Three: boot need to press the F1 key to enter, mainly because
the BIOS settings and real hardware data inconsistent, can be
divided into the following circumstances:
1, in fact, no floppy or floppy drive is broken, and the BIOS
is provided with a floppy drive, which causes the press F1 to
continue. 2, originally hung two hard disk, in the BIOS set into a double
hard disk, and then remove one of them, but forget to change
the BIOS settings, there will be this problem.
3, the motherboard battery is not power, it will cause data loss,
resulting in this fault.
4, restart the system, enter the BIOS settings, and found that
the floppy drive is set to 1.44M, but in fact there is no floppy
drive in the chassis, the set to NONE, troubleshooting.
=====================================================================================
曾经有很多人问过这样的问题，下面把此类问题做一下总结，希望对大家有所帮助。
1、监视功能发现错误，进入电源管理设置查看详细资料，按F1键继续，按DEL键进入设置
中文：监视功能发现错误，进入电源管理设置察看详细资料，按F1键继续开机程序，按del键进入COMS设置。
解释：有的主板具备硬件的监视功能，可以设定主板与CPU的温度监视、电压调整器的电压输出准位监视和对各个风扇转速的监视，当
上述监视功能在开机时发觉有异常情况，那么便会出现上述这段话，这时可以进入COMS设置选择电源管理设置，在右面的* * * * * *、风机监测监控和热** ** **察看是哪部分发出了异常电压监控，然后再加以解决。 2、PRI从动ATAPI lncompatible按F1继续
可能是你的光驱没接好或有故障，最好在CMOS中将各IDE口设为自动。
3、按F1继续，德尔进入安装程序
开机后按del进入BIOS，在选择软驱中选择没有后按F10保存就可以了
4、CMOS校验和错误－默认加载
按F1继续吗？进入安装程序
08／09／2000－i810－ite8712－6a69me1cc－00
CMOS电池没电。
5，警告！CPU已更改！请输入CPU速度CMOS设置，并记得退出前保存！
这说明BIOS设置被冲掉了，要重新设置BIOS（又叫做CMOS设置）。开机按住“DEL”键进入设置，看你的主板说明书。你的CPU频率是多少？在BIOS中要选好外频，倍频反正是锁定的。外频总是66、100或133，要看CPU型号，从低往高设置。如果是奖的BIOS设置，在首页就选频率/电压控制（频率/电压的控制），使用此菜单可以对频率、电压进行特别的设定其中”。时钟由Slight Adjust（时钟频率微调）”允许你选择CPU时钟频率。各种主板的BIOS设置有差别，可以参考自己的主板说明书进行调整。
6、CPU已更改，请重新输入CMOS设置中的CPU设置，并记得在退出前保存！
有些主板上有个外频跳线，默认为100MHz，还有些主板不支持自动调频。你只要进BIOS里把外频设置成你的CPU标准外频就可以了，倍频方面一般是自动设置，最好不要超频。
如果上述解决办法都不能解决的话，你可以检查CMOS旁边电路是否有烧坏的迹象，我的机器就是因为CMOS旁边的电路有问题，上述机决方法都试过了也没用，最后一烙铁就搞定呵呵，不妨你也试试！
=====================================================================================
开机需要按F1才能进入系统的故障排除
在通常情况下，要求按F1进入系统都是系统的BIOS设置有不影响系统启动的小问题所致，所以请检查BIOS里的硬件信息设置与实际不符之处。
一般常见故障是：
1、主板上的电池没电了。
解决方法：换主板电池。
2、你设置了软驱启动，但是你的软驱有问题。
解决方法：
A, boot, press DEL to enter BIOS, boot startup sequence, turn off floppy drive.
B, turn off boot floppy detection function:
Start the computer, then press Del to enter the BIOS and set
the main interface;
Select the Advanced BIOS Features setting item and press enter
to enter;
Set the "Boot Up Floppy Seek" to "Disabled" so that you can turn
off the boot software detection function.
=====================================================================================
Press F1 to enter the (boot) system solution
1, BIOS, ROM, check, sum, error, System, halted
(BIOS information is detected when total checksum is found,
system locked)
Solution: this error is not usually encountered, this
information is mostly on the motherboard BIOS refresh is not
complete will appear, the only way is to refresh the treatment
BIOS, but no guarantee of success.
2, CMOS, battery, failed
(CMOS battery failure) Solution: This shows that the CMOS battery is out of power. Just
remove the button cell on the motherboard and replace it with
a new battery. Most motherboards use 3V's button batteries, so
don't buy 5V batteries! As long as you look at the surface of
the battery carefully, you can clearly see the word "3V" on it.
3, CMOS, check, sum, error-Defaults, loaded
(CMOS finds errors when performing full checking and loads
system defaults)
Solution: this situation is usually caused by a lack of battery
power. It is recommended to replace the battery first. If the
problem is still not resolved, so that CMOS RAM and CMOS RAM
may issue, because our person is unable to repair, if the dealer
handles the motherboard is still under warranty please contact
the motherboard manufacturer or to buy.
4, Display, switch, is, set, incorrectly
(display switch configuration error)
Solution: as long as your motherboard is not old, this
information will certainly not appear. In general, there is a
route on the old motherboard to set the screen to monochrome
or color. This information indicates that the settings on the
motherboard are inconsistent with the CMOS settings, so just
judge who is correct for the motherboard and the CMOS settings,
and then update the wrong settings.
5, Floppy, disk (s), fail or Floppy, disk (s), fail (80) or
Floppy, disk (s), fail (40)
(floppy drive failed)
Solution: check that the floppy drive's data line is properly
connected to see if there is any reverse or loose connection.
Don't tell me, the plug is not connected! If you do not have
a floppy drive, it is recommended to set "Drive A" to "None"
in the CMOS Setup program". I'd like to find a good floppy to
try it on. To verify that the original floppy drive is out of
order.
6, Hard, disk (s), diagnosis, fail
An error occurred while performing the hard disk diagnostics
Solution: this information appears, in general, that the hard
disk itself is out of order. You can try hard disk to another
computer. If the problem is not solved, it could be a serious
physical failure on this hard disk.
7, Hard, disk (s), install, failure
(hard disk installation failed)
Solution: check whether the power line or data line of the hard
disk is properly connected. If the jumper with a IDE line to
connect two IDE device settings are the same, as long as the
jumper these two IDE devices can be set different (generally
will be the main hard disk is Master, another is Slave). 8, Hard, disk (s), initializing (Please, wait, a, moment)... )
(initializing hard disk, please wait a moment)
Solution: this information is not visible on newer disks, but
on older disks, this information is seen because it is slower.
9, Hardware, Monitor, found, an, error,
进入详情的电源管理设置，按F1键继续，按DEL键进入设置
（监视功能发现错误，进入“电源管理设置”查看详细资料，按F1键继续开机程序，按del键进入CMOS设置）
解决方案：有的主板具备硬件的监测功能，可以设定主板与CPU的温度监测、电压调整器的电压输出准位监测和对各个风扇转速的监测，当上述监测功能在开机时发觉有异常情况才会出现这个信息，这时可以进入CMOS设置，查看“电源管理设置”中哪方面出现异常，然后加以解决。
10、键盘错误或没有键盘出现
（键盘错误或者未接键盘）
解决方案：检查一下键盘的连线是否松动或者损坏，一些品质较次的键盘往往很容易出现此信息。
11、内存测试失败
（内存检测失败） 解决方案：通常这种情形是因为内存不兼容或故障所致。建议你重新插拔一下内存条，也许是因为内存条间互相不兼容。建议以每次开机一条内存的方式分批测试，找出故障的内存，把它拿掉或送修即可。
12、重载启用默认加载
（当前CMOS设定无法启动系统，载入BIOS中的预设值以便启动系统）
解决方案：一般是在CMOS设置内的设置出现错误才会出现此信息，只要重新进入CMOS设置选择”加载默认设置”载入系统原来的设定值，然后重新启动即可。
13、按下TAB显示后屏幕
（按选项卡键可以切换屏幕显示）
解决方案：有些主板厂商会以自己设计的开机显示画面来取代BIOS预设的开机显示画面，而此信息是要告诉用户可以按”选项卡的“键把厂商自己设计的开机显示画面和BIOS预设的开机显示画面进行切换。
14、按ESC跳过内存测试
（正在进行内存检测，可按下ESC键跳过）
解决方案：当然你也可以按ESC键结束内存检测，或者等待检测通过。如果你不想等待的话，进入CMOS设置后选择“BIOS设置”，将其中的“快速开机自我测试”设为“已启用”，储存后重新启动即可。
15、主努力失败或初级奴隶努力失败或二主人的努力失败或中等奴隶努力失败
（检测硬盘失败）
解决方案：可能是CMOS设置不当，比如说没有从盘但在CMOS设置里设为有从盘，那么就会出现错误，这时可以进入CMOS设置对硬盘进行自动检测，也可能是硬盘的电源线，数据线可能未接好或者硬盘跳线设置不当。
16、从硬盘恢复开机，开机后屏幕显示
（从硬盘恢复开机，按选项卡显示开机自检画面）
解决方案：这是因为有些主板的BIOS提供了”挂起到磁盘（将硬盘挂起）”的功能，如果我们用挂起到磁盘的方式来关机，那么我们在下次开机时就会显示此提示消息。
发布评论