2024年2月26日发(作者：)
1. HOMOGENIZATION (see notes 1-3)
a. Tissues
TRIZOL®
Reagent
Cat. No. 15596-026
Store at 2 to 8°C.
Size: 100 ml
WARNING: Toxic in contact with skin and if swallowed. Causes burns. After
contact with skin, wash immediately with plenty of detergent and water. If you feel
unwell, seek medical advice (show label where possible). Phenol (108-95-2) and Other
Components (NJTSRN 80100437-5000p).
TRIZOL has demonstrated stability of 12 months when stored at room temperature. However, we
recommend storage at 2 to 8°C for optimal performance.
Description:
TRIZOL Reagent ( No.5,346,994) is a ready-to-use reagent for the isolation of total RNA
from cells and tissues. The reagent, a mono-phasic solution of phenol and guanidine isothiocyanate,
is an improvement to the single-step RNA isolation method developed by Chomczynski and Sacchi
(1). During sample homogenization or lysis, TRIZOL Reagent maintains the integrity of the RNA,
while disrupting cells and dissolving cell components. Addition of chloroform followed by
centrifugation, separates the solution into an aqueous phase and an organic phase. RNA remains
exclusively in the aqueous phase. After transfer of the aqueous phase, the RNA is recovered by
precipitation with isopropyl alcohol. After removal of the aqueous phase, the DNA and proteins in
the sample can be recovered by sequential precipitation (2). Precipitation with ethanol yields DNA
from the interphase, and an additional precipitation with isopropyl alcohol yields proteins from the
organic phase (2). Copurification of the DNA may be useful for normalizing RNA yields from
sample to sample.
This technique performs well with small quantities of tissue (50-100 mg) and cells (5 × 106), and
large quantities of tissue (≥1 g) and cells (>107), of human, animal, plant, or bacterial origin. The
simplicity of the TRIZOL Reagent method allows simultaneous processing of a large number of
samples. The entire procedure can be completed in one hour. Total RNA isolated by TRIZOL
Reagent is free of protein and DNA contamination. It can be used for Northern blot analysis, dot blot
hybridization, poly (A)+ selection, in vitro translation, RNase protection assay, and molecular
cloning. For use in the polymerase chain reaction (PCR*), treatment of the isolated RNA with
amplification grade DNase I (Cat. No. 18068) is recommended when the two primers lie within a
single exon.
TRIZOL Reagent facilitates isolation of a variety of RNA species of large or small molecular size.
For example, RNA isolated from rat liver, electrophoresed on an agarose gel, and stained with
ethidium bromide, shows discrete bands of high molecular weight RNA between 7 kb and 15 kb in
size, (composed of mRNA’s and hnRNA’s) two predominant ribosomal RNA bands at ~5 kb (28S)
and at ~2 kb (18S), and low molecular weight RNA between 0.1 and 0.3 kb (tRNA, 5S). The
isolated RNA has an A260/A280 ratio ≥1.8 when diluted into TE.
Precautions for Preventing RNase Contamination:
RNases can be introduced accidentally into the RNA preparation at any point in the isolation
procedure through improper technique. Because RNase activity is difficult to inhibit, it is essential
to prevent its introduction. The following guidelines should be observed when working with RNA.
•
Always wear disposable gloves. Skin often contains bacteria and molds that can contaminate
an RNA preparation and be a source of RNases. Practice good microbiological technique to
prevent microbial contamination.
•
Use sterile, disposable plasticware and automatic pipettes reserved for RNA work to prevent
cross-contamination with RNases from shared equipment. For example, a laboratory that is
using RNA probes will likely be using RNase A or T1 to reduce background on filters, and any
nondisposable items (such as automatic pipettes) can be rich sources of RNases.
•
In the presence of TRIZOL Reagent, RNA is protected from RNase contamination. Downstream
sample handling requires that nondisposable glassware or plasticware be RNase-free. Glass
items can be baked at 150°C for 4 hours, and plastic items can be soaked for 10 minutes in 0.5
M NaOH, rinsed thoroughly with water, and autoclaved.
Other Precautions:
•
Use of disposable tubes made of clear polypropylene is recommended when working with less
than 2-ml volumes of TRIZOL Reagent.
•
For larger volumes, use glass (Corex) or polypropylene tubes, and test to be sure that the tubes
can withstand 12,000 × g with TRIZOL Reagent and chloroform. Do not use tubes that leak or
crack.
•
Carefully equilibrate the weights of the tubes prior to centrifugation.
•
Glass tubes must be sealed with parafilm topped with a layer of foil, and polypropylene tubes
must be capped before centrifugation.
INSTRUCTIONS FOR RNA ISOLATION:
Caution: When working with TRIZOL Reagent use gloves and eye protection (shield, safety
goggles). Avoid contact with skin or clothing. Use in a chemical fume hood. Avoid breathing
vapor.
Homogenize tissue samples in 1 ml of TRIZOL Reagent per 50-100 mg of tissue using a
glass-Teflon® or power homogenizer (Polytron, or Tekmar's TISSUMIZER® or
equivalent). The sample volume should not exceed 10% of the volume of TRIZOL
Reagent used for homogenization.
b. Cells Grown in Monolayer
Lyse cells directly in a culture dish by adding 1 ml of TRIZOL Reagent to a 3.5 cm
diameter dish, and passing the cell lysate several times through a pipette. The amount of
TRIZOL Reagent added is based on the area of the culture dish (1 ml per 10 cm2) and not
on the number of cells present. An insufficient amount of TRIZOL Reagent may result in
contamination of the isolated RNA with DNA.
c.
Cells Grown in Suspension
Pellet cells by centrifugation. Lyse cells in TRIZOL Reagent by repetitive pipetting. Use
1 ml of the reagent per 5-10 × 106 of animal, plant or yeast cells, or per 1 × 107 bacterial
cells. Washing cells before addition of TRIZOL Reagent should be avoided as this
increases the possibility of mRNA degradation. Disruption of some yeast and bacterial
cells may require the use of a homogenizer.
OPTIONAL: An additional isolation step may be required for samples with high content of
proteins, fat, polysaccharides or extracellular material such as muscles, fat tissue, and tuberous
parts of plants. Following homogenization, remove insoluble material from the homogenate by
centrifugation at 12,000 × g for 10 minutes at 2 to 8°C. The resulting pellet contains
extracellular membranes, polysaccharides, and high molecular weight DNA, while the
supernatant contains RNA. In samples from fat tissue, an excess of fat collects as a top layer
which should be removed. In each case, transfer the cleared homogenate solution to a fresh
tube and proceed with chloroform addition and phase separation as described.
2. PHASE SEPARATION
Incubate the homogenized samples for 5 minutes at 15 to 30°C to permit the complete
dissociation of nucleoprotein complexes. Add 0.2 ml of chloroform per 1 ml of TRIZOL
Reagent. Cap sample tubes securely. Shake tubes vigorously by hand for 15 seconds and
incubate them at 15 to 30°C for 2 to 3 minutes. Centrifuge the samples at no more than 12,000
× g for 15 minutes at 2 to 8°C. Following centrifugation, the mixture separates into a lower
red, phenol-chloroform phase, an interphase, and a colorless upper aqueous phase. RNA
remains exclusively in the aqueous phase. The volume of the aqueous phase is about 60% of
the volume of TRIZOL Reagent used for homogenization.
3. RNA PRECIPITATION
Transfer the aqueous phase to a fresh tube, and save the organic phase if isolation of DNA or
protein is desired. Precipitate the RNA from the aqueous phase by mixing with isopropyl
alcohol. Use 0.5 ml of isopropyl alcohol per 1 ml of TRIZOL Reagent used for the initial
homogenization. Incubate samples at 15 to 30°C for 10 minutes and centrifuge at no more than
12,000 × g for 10 minutes at 2 to 8°C. The RNA precipitate, often invisible before
centrifugation, forms a gel-like pellet on the side and bottom of the tube.
4.
RNA WASH
Remove the supernatant. Wash the RNA pellet once with 75% ethanol, adding at least 1 ml of
75% ethanol per 1 ml of TRIZOL Reagent used for the initial homogenization. Mix the sample
by vortexing and centrifuge at no more than 7,500 × g for 5 minutes at 2 to 8°C.
5.
REDISSOLVING THE RNA
At the end of the procedure, briefly dry the RNA pellet (air-dry or vacuum-dry for 5-10
minutes). Do not dry the RNA by centrifugation under vacuum. It is important not to let the
RNA pellet dry completely as this will greatly decrease its solubility. Partially dissolved RNA
samples have an A260/280 ratio < 1.6. Dissolve RNA in RNase-free water or 0.5% SDS solution
by passing the solution a few times through a pipette tip, and incubating for 10 minutes at 55 to
60°C. (Avoid SDS when RNA will be used in subsequent enzymatic reactions.) RNA can also
be redissolved in 100% formamide (deionized) and stored at -70°C (5).
RNA Isolation Notes:
1.
Isolation of RNA from small quantities of tissue (1 to 10 mg) or Cell (102 to 104) Samples:
Add 800 µl of TRIZOL to the tissue or cells. Following sample lysis, add chloroform and
proceed with the phase separation as described in step 2. Prior to precipitating the RNA with
isopropyl alcohol, add 5-10 µg RNase-free glycogen (Cat. No 10814) as carrier to the
aqueous phase. To reduce viscosity, shear the genomic DNA with 2 passes through a 26
gauge needle prior to chloroform addition. The glycogen remains in the aqueous phase and
is co-precipitated with the RNA. It does not inhibit first-strand synthesis at concentrations up
to 4 mg/ml and does not inhibit PCR.
2.
After homogenization and before addition of chloroform, samples can be stored at -60 to -70°C
for at least one month. The RNA precipitate (step 4, RNA WASH) can be stored in 75%
ethanol at 2 to 8°C for at least one week, or at least one year at –5 to -20°C.
3. Table-top centrifuges that can attain a maximum of 2,600 × g are suitable for use in these
protocols if the centrifugation time is increased to 30-60 minutes in steps 2 and 3.
INSTRUCTIONS FOR DNA ISOLATION:
Unless otherwise stated, the procedure is carried out at 15 to 30°C, and reagents are at 15 to 30°C.
Reagents required, but not supplied:
•
Chloroform
•
Isopropyl alcohol
•
75% Ethanol (in DEPC-treated water)
•
RNase-free water or 0.5% SDS solution [To prepare RNase-free water, draw water into
RNase-free glass bottles. Add diethylpyrocarbonate (DEPC) to 0.01% (v/v). Let stand
overnight and autoclave. The SDS solution must be prepared using DEPC-treated, autoclaved
water.]
After complete removal of the aqueous phase, as described in the RNA isolation protocol, the DNA
in the interphase and phenol phase from the initial homogenate may be isolated. Following
precipitation and a series of washes, the DNA is solubilized in 8 mM NaOH. Full recovery of DNA
from tissues and culture cells permits the use of TRIZOL Reagent for the determination of the DNA
content in analyzed samples (2). Simultaneous extraction of genomic DNA allows for normalization
of the results of Northern analysis per genomic DNA instead of the more variable total RNA or
tissue weight. (Depending on the source, the DNA pellet obtained may require additional
purification (e.g., phenol extraction) prior to other applications.
Reagents required, but not supplied:
•
Ethanol
•
0.1 M Sodium citrate in 10% ethanol
•
75% Ethanol
•
8 mM NaOH
Unless otherwise stated, the procedure is carried out at 15 to 30°C.
1. DNA PRECIPITATION
Remove the remaining aqueous phase overlying the interphase, and precipitate the DNA from
the interphase and organic phase with ethanol. Add 0.3 ml of 100% ethanol per 1 ml of
TRIZOL Reagent used for the initial homogenization, and mix samples by inversion. Next,
store the samples at 15 to 30°C for 2-3 minutes and sediment DNA by centrifugation at no
more than 2,000
Careful removal of the aqueous phase is critical for the quality of the isolated
× g for 5 minutes at 2 to 8°C.
DNA.
2. DNA WASH
Remove the phenol-ethanol supernatant, and if desired, save it for protein isolation. Wash the
DNA pellet twice in a solution containing 0.1 M sodium citrate in 10% ethanol. Use 1 ml of
the solution per 1 ml of TRIZOL Reagent used for the initial homogenization. At each wash,
store the DNA pellet in the washing solution for 30 minutes at 15 to 30°C (with periodic
mixing) and centrifuge at 2,000 × g for 5 minutes at 2 to 8°C. Following these two washes,
suspend the DNA pellet in 75% ethanol (1.5-2 ml of 75% ethanol per 1 ml TRIZOL Reagent),
store for 10-20 minutes at 15 to 30°C (with periodic mixing) and centrifuge at 2,000 × g for 5
minutes at 2 to 8°C.
An additional wash in 0.1 M sodium citrate-10% ethanol solution is required for large pellets
containing > 200
µg DNA or large amounts of a non-DNA material.
3. REDISSOLVING THE DNA
Air dry the DNA 5 to 15 minutes in an open tube. (DO NOT DRY UNDER
CENTRIFUGATION; it will be more difficult to dissolve.) Dissolve DNA in 8 mM NaOH
such that the concentration of DNA is 0.2 – 0.3 µg/µl. Typically add 300 – 600 µl of 8 mM
NaOH to DNA isolated from 107 cells or 50 – 70 mg of tissue. Resuspending in weak base is
HIGHLY recommended since isolated DNA does not resuspend well in water or in Tris
buffers. The pH of the 8 mM NaOH is only ~9 and should be easily adjusted with TE or
HEPES once the DNA is in solution. At this stage, the DNA preparations (especially from
tissues) may contain insoluble gel-like material (fragments of membranes, etc.) Remove the
insoluble material by centrifugation at >12,000 × g for 10 minutes. Transfer the supernatant
containing the DNA to a new tube. DNA solubilized in 8 mM NaOH can be stored overnight
at 4°C; for prolonged storage, samples should be adjusted with HEPES to pH 7-8 (see table)
and supplemented with 1 mM EDTA. Once the pH is adjusted, DNA can be stored at 4°C or –20°C.
Quantitation and Expected Yields of DNA
Take an aliquot of the DNA preparation solubilized in 8 mM NaOH, mix it with water and measure
the A260 of the resulting solution. Calculate the DNA content using the A260 value for double-stranded DNA. One A260 unit equals 50
µg of double-stranded DNA/ml. For calculation of cell
number in analyzed samples, assume that the amount of DNA per 1 × 106 diploid cells of human, rat,
and mouse origin equals: 7.1
µg, 6.5
µg, and 5.8
µg, respectively (3).
Applications:
Amplification of DNA by PCR:
After redissolving the DNA in 8 mM NaOH, adjust the pH to 8.4 with 0.1 M HEPES (see table).
Add 0.1 to 1.0
µg of the DNA sample to your PCR reaction mixture and perform the standard PCR
protocol.
Restriction endonuclease reactions:
Adjust the pH of the DNA solution to a required value using HEPES (see table). Alternatively,
samples may be dialyzed against 1 mM EDTA, pH 7 to pH 8.0. Use 3-5 units of enzyme per
microgram of DNA. Use the conditions recommended by the manufacturer for the particular
enzyme, and allow the reaction to proceed for 3 to 24 h. In a typical assay, 80-90% of the DNA is
digestible.
pH Adjustment of DNA Samples Dissolved in 8 mM NaOH:
(For 1 ml of 8 mM NaOH use the following amounts of 0.1 M or 1 M HEPES, free acid.)
Final pH 0.1 M HEPES (µl) Final pH 1 M HEPES (µl)
8.4 86 7.2 23
8.2 93 7.0 32
8.0 101
7.8 117
7.5 159
DNA Isolation Notes:
1. The phenol phase and interphase can be stored at 2 to 8°C overnight.
2. Samples suspended in 75% ethanol can be stored at 2 to 8°C for months.
3. Samples dissolved in 8 mM NaOH can be stored overnight at 2 to 8°C. For long-term storage,
adjust the pH to 7-8, and adjust the EDTA concentration to 1 mM.
INSTRUCTIONS FOR PROTEIN ISOLATION:
Proteins are isolated from the phenol-ethanol supernatant obtained after precipitation of DNA with
ethanol (step 1, DNA PRECIPITATION). The resulting preparation can be analyzed for the
presence of specific proteins by Western blotting (2).
Reagents required, but not supplied:
•
•
Isopropyl alcohol
•
0.3 M Guanidine hydrochloride in 95% ethanol
•
Ethanol
1% SDS
1. PROTEIN PRECIPITATION
Precipitate proteins from the phenol-ethanol supernatant (approximate volume 0.8 ml per 1 ml
of TRIZOL Reagent) with isopropyl alcohol. Add 1.5 ml of isopropanol per 1 ml of TRIZOL
Reagent used for the initial homogenization. Store samples for 10 minutes at 15 to 30°C, and
sediment the protein precipitate at 12,000 × g for 10 minutes at 2 to 8°C.
2. PROTEIN WASH
Remove the supernatant and wash the protein pellet 3 times in a solution containing 0.3 M
guanidine hydrochloride in 95% ethanol. Add 2 ml of wash solution per1 ml of TRIZOL
Reagent used for the initial homogenization. During each wash cycle, store the protein pellet
in the wash solution for 20 minutes at 15 to 30°C and centrifuge at 7,500 × g for 5 minutes at 2
to 8°C. After the final wash, vortex the protein pellet in 2 ml of ethanol. Store the protein
pellet in ethanol for 20 minutes at 15 to 30°C and centrifuge at 7,500 × g for 5 minutes at 2 to
8°C.
3. REDISSOLVING THE PROTEIN PELLET
Vacuum dry the protein pellet for 5-10 minutes. Dissolve it in 1% SDS by pipetting. Complete
dissolution of the protein pellet may require incubating the sample at 50°C. Sediment any
insoluble material by centrifugation at 10,000 × g for 10 minutes at 2 to 8°C, and transfer the
supernatant to a fresh tube. The sample is ready for use in Western blotting or may be stored at
-5 to -20°C for future use.
Protein Isolation Notes:
1. The protein pellet suspended in 0.3 M guanidine hydrochloride-95% ethanol or in ethanol can
be stored for at least one month at 2 to 8°C, or for at least one year at -5 to -20°C.
2. The following protocol is an alternative approach that allows for more efficient recovery of
proteins. Dialyze the phenol-ethanol supernatant against three changes of 0.1% SDS at 2 to
8°C. Centrifuge the dialyzed material at 10,000 × g for 10 minutes. Use the clear supernatant
for Western blotting.
3.
Proteins may be quantified by the Bradford method as long as the concentration of SDS is low
enough (<0.1%) so that it will not interfere. Methods that do not have detergent-interface
problems, and that do not rely on A
cause overestimation of protein concentrations).
260/A280 measurements may be used (traces of phenol may
Troubleshooting Guide:
RNA ISOLATION
•Expected yields of RNA per mg of tissue or 1
× 106 cultured cells
Kidney,
Liver and spleen, 6-10
µ
g
g
µ Placenta,
Skeletal muscles and brain, 1-1.5
3-4
µ Epithelial cells (1
1-4 g
g
µ× 106 cultured cells), 8-15
µ Fibroblasts, (1 × 106 cultured cells) 5-7
g
µ•Low yield
g
Incomplete homogenization or lysis of samples.
•AFinal RNA pellet incompletely redissolved.
260/ARNA sample was diluted in water instead of TE prior to spectrophotometric analysis. Low
280 ratio <1.65
ionic strength and low pH solutions increase absorbance at 280 nm (6,7).
Sample homogenized in too small a reagent volume.
Following homogenization, samples were not stored at room temperature for 5 minutes.
The aqueous phase was contaminated with the phenol phase.
•RNA degradation
Incomplete dissolution of the final RNA pellet.
Tissues were not immediately processed or frozen after removal from the animal.
Samples used for isolation, or the isolated RNA preparations were stored at -5 to-20°C, instead
of -60 to -70°C.
Cells were dispersed by trypsin digestion.
Aqueous solutions or tubes were not RNase-free.
•DNA contamination
Formaldehyde used for agarose-gel electrophoresis had a pH below 3.5.
Sample homogenized in too small a reagent volume.
Samples used for the isolation contained organic solvents (e.g., ethanol, DMSO), strong
• Proteoglycan and polysaccharide contamination
buffers, or alkaline solution.
The following modification of the RNA precipitation (step 3) removes these contaminating
compounds from the isolated RNA. Add to the aqueous phase 0.25 ml of isopropanol followed
by 0.25 ml of a high salt precipitation solution (0.8 M sodium citrate and 1.2 M NaCl) per 1 ml
of TRIproceed with the isolation as described in the protocol. The modified precipitation effectively
ZOL Reagent used for the homogenization. Mix the resulting solution, centrifuge and
precipitates RNA while maintaining polysaccharides and proteoglycans in a soluble form. A
combination of the modified precipitation with an additional centrifugation of the initial
homogenate (note 2, RNA isolation protocol) is required to isolate pure RNA from plant
material containing a very high level of polysaccharides.
DNA ISOLATION
•Expected yields of DNA per mg of tissue or 1
Liver and kidney, 3-4
× 106 cultured cells
µg
Skeletal muscles, brain, and placenta 2-3
µ Fibroblasts,
Cultured human, rat, and mouse cells (1
•Low yield
5-7 g
× 10g
6), 5-7
µg
µ
Incomplete homogenization or lysis of samples.
•AFinal DNA pellet incompletely redissolved.
260/280DNA sample was diluted in water instead of TE prior to spectrophotometric analysis.
ratio <1.70
Phenol was not sufficiently removed from the DNA preparation. Wash the DNA pellet an
•DNA degradation
additional time with 0.1 M sodium citrate in 10% ethanol.
Tissues were not immediately processed or frozen after removal from the animal.
Samples used for isolation, or the isolated RNA preparations were stored at -5 to-20°C, instead
of -60 to -70°C.
•RNA contamination
Samples were homogenized with a Polytron or other high speed homogenizer.
Incomplete removal of aqueous phase.
•Other applications
DNA pellet insufficiently washed with 0.1 M sodium citrate in 10% ethanol.
Prior to use in PCR amplification, adjust the pH to 8.4.
For digestion of the DNA with restriction endonucleases, adjust the pH to the desired value,
use 3-5 units of enzyme per
optimal conditions for the particular enzyme. Typically 80-90% of the DNA is digested.
µg of DNA, and allow the reaction to go for 3-24 hours under
PROTEIN ISOLATION
•Low yield
Incomplete homogenization or lysis of samples.
•Protein degradation
Final DNA pellet incompletely redissolved.
•Band deformation in PAGE
Tissues were not immediately processed or frozen after removing from the animal.
Protein pellet insufficiently washed.
References:
1.
2.
Chomczynski, P., and Sacchi, N. (1987) Anal. Biochem.
3. Ausubel,
Chomczynski, P. (1993)
162, 156.
F.M., , eds. (1990)
Biotechniques 15,Current Protocols in Molecular Biology 532.
4.
Publishing Assoc. and Wiley-Interscience, New York, p.A.1.5.
, Vol.2, Greene
5.
Simms, D., Cizdziel, P.E., Chomczynski, P. (1993) FOCUS® 15, 99.
6.
Bracete, A.M., Fox, D.K., and Simms, D. (1998) FOCUS 20, 82).
7.
Wilfinger, W., Mackey, K. and Chomczynski, P. (1997)
Fox, D.K. (1998) F 37.
BioTechniques 22, 474.
OCUS 20,Teflon® is a registered trademark of E. I. Du Pont de Nemours & Co.
TISSUMIZER®
is a registered trademark of Tekmar Co.
TRIZOL ® is a registered trademark of Molecular Research Center, Inc.
*PCR is covered by a patent held by Hoffman LaRoche Corporation.
Cat No. 15596-026
发布评论