2024年3月21日发(作者：)
1.
Gear with precise design and high quality closely combines with thermal refining worm.
精密设计高品质齿轮与调质处理蜗杆紧密结合。
2.
Utilizing a state of the art process of controlled thermal treatment for hardening and tempering.
先进的可控气氛热处理生产线对产品进行调质处理。
3.
Alloy steel 40Cr quenched and tempered to HRC 28 was chosen to investigate the regularities of the
change of surface integrity after grinding.
本文叙述了40Cr合金结构钢在调质处理状态(HRC28)下,经磨削加工后表面质量的变化规律。
4.
The results show that the main causes of fracture is composition segregation and low strength resut
from no quenching and tempering treatment.
结果表明，产生断裂的主要原因是材料内部成分偏析及未按要求对材料进行调质处理导致材料的强度较低。
5.
Abstract: The authors give an all-round and systematic exposition of the function of conditioning
treatment in the course of wheat processing, its impact on operation and the method of controlling the
appropriate moisture content in the wheat to IBK, meanwhile set forth a series of methods of shortening
dampening cycles, the direction in developing auto-damping controllers as well as the significance in
doing a good conditioning job.
文摘:全面系统地阐述了小麦加工过程中调质处理的作用，对操的影响及最佳入磨水分的控制方法，并提出
一系列缩短润麦时间的方法，小麦自动着水控制仪的研究方向和认真做好调质工作的意义。
6.
By temper rapid cooling process, σs of HSLC steel ZJ330 produced by CSP process are increased
from 340MPa to about 410MPa and from 410MPa to 450MPa, respectively.
通过亚调质处理,使薄板坯连铸连轧HSLC钢ZJ330的屈服强度从340MPa进一步提高到410MPa左
右,SPA-H集装箱板的屈服强度从410MPa提高到450MPa;
7.
HT Sub-factory : complete process of annealing, quenching, tempering, quenching and tempering,
solution treatment etc.
热处理厂：可完成退火,正火,回火，调质,固溶处理等工艺.
8.
After ASTM D 1037 6-cycle accelerated aging, and 48-hours equilibrium, the performances showed
well.
经过ASTM D1037六个老化周期，调质48小时处理后，板材的耐水性、尺寸稳定性表现的非常好。
9.
Normalizing at 860℃, the strength and plasticity of the (UHCS) is higher than that of harden and
tempered middle carbon alloy steels.
860℃正火处理,强度和塑性较传统中碳合金调质钢的高。
10.
the AV was minimum 1.52 mgKOH/g after pelletizing with ring die under the conditions of moisture
content required for pelletizing 16.61% and conditioning temperature 85℃;
环模制粒后酸价最低为1.52 mgKOH/g,其处理条件:入模水分为16.61%,调质温度85℃;
1
11.
The results show that the main causes of fracture is composition segregation and low strength resut
from no quenching and tempering treatment.
结果表明，产生断裂的主要原因是材料内部成分偏析及未按要求对材料进行调质处理导致材料的强度较低。
12.
The results show that the main causes of fracture is composition segregation and low strength resut
from no quenching and tempering treatment.
结果表明，产生断裂的主要原因是材料内部成分偏析及未按要求对材料进行调质处理导致材料的强度较低。
13.
Abstract: The authors give an all-round and systematic exposition of the function of conditioning
treatment in the course of wheat processing, its impact on operation and the method of controlling the
appropriate moisture content in the wheat to IBK, meanwhile set forth a series of methods of shortening
dampening cycles, the direction in developing auto-damping controllers as well as the significance in
doing a good conditioning job.
文摘:全面系统地阐述了小麦加工过程中调质处理的作用，对操作的影响及最佳入磨水分的控制方法，并提
出一系列缩短润麦时间的方法，小麦自动着水控制仪的研究方向和认真做好调质工作的意义。
14.
By temper rapid cooling process, σs of HSLC steel ZJ330 produced by CSP process are increased
from 340MPa to about 410MPa and from 410MPa to 450MPa, respectively.
通过亚调质处理,使薄板坯连铸连轧HSLC钢ZJ330的屈服强度从340MPa进一步提高到410MPa左
右,SPA-H集装箱板的屈服强度从410MPa提高到450MPa;
15.
Developing of 38Si7 Hardened and Tempered Spring Steel(DIN)
德标38Si7调质弹簧钢的开发
16.
To subject(a proposition) to obversion.
用换质法说明（事物）将一命题作换质处理
17.
800MPa FERRITE-PEARLITE STEEL WITH GOOD TOUGHNESS
800兆帕级高韧性非调质钢
18.
FLUTTER CONTROL OF LARGE-SPAN BRIDGES BY USING PASSIVE TUNED MASS DAMPER
用调质阻尼器控制桥梁颤振
19.
Study on the flue gas spray and wet enhancement technology in the flue of a boiler end part
锅炉尾部烟道直接喷水调质技术的研究
20.
R&D of Conn-rod of High-strength Micro Alloyed
高强度非调质钢连杆的研制
21.
Study on Weldability of 20MnMo Casting and Forging Low Alloy QT Steels
20MnMo低合金调质铸锻钢焊接性研究
22.
To subject(a proposition) to obversion.
用换质法说明（事物）将一命题作换质处理
2
发布评论