2024年4月3日发(作者：)
2D product drawing 2D产品图
2K injection machine 2K模
2‐plate mold 二板模
3 plate 3板模
3‐plate mold 三板模
3‐plate pin gate 三板模点水口
A plate A板
A/B plate steel A/B板材料
Adjust melt temperature(increase to relieve molded-in stress, decrease to avoid over
packing) 调节溶胶温度（升温为改善进胶，降温为避免多胶）
Air bubble 气泡
Air bubble 气泡
Air cylinder 气缸
alter gate position or increase gate size
更改进胶点的位置或增大进胶口的尺寸
Angle lifter 斜顶
Angle pin 斜导柱
Angle pin 斜导柱
Application for inspection
Automatic unscrewing mold 自动脱螺纹
B plate B板
Baffle 隔水片
Balanced runner 平衡水口系统
Balancing plates/pillars 平衡块，杆
Ball screw 波仔螺丝
Ball screw 波子螺丝
Banana gate 香蕉水口
Band saw 锯床
Bearing 轴承
Berilium copper/ampco 铍铜
Big grinding machines 大水磨
Black
specks/emdedded contaminates 黑斑
black spots, bronze steaks 黑点，棕色条纹
Blade ejector 扁顶针
Blister/blistering 气泡
blisters 鼓起
Blue die 蓝丹
Blush 发赤
Bolts 螺栓
Bonded area
Bonded goods
Boss 柱位
Boss 柱位
Bottom clamping plate 底板
Brand insert/ mark insert 商标，标志
brittleness 脆
Brittleness脆裂
bubble 气泡
Bubbles 气泡
Burn mark 烧焦
Burn marks‐ air or gas 烧焦
Cavity insert 前模镶件
Cavity insert 前模镶件
Cavity number 模穴
Cavity number 穴数
Cavity 前模
Cavity/ core insert 前/后，模镶件
Cavity/core finish 前后模表面处理
Cavity/core pin 前/后模镶件
Center sprue/sprue gate 中心进浇/直浇口
Chain wheel 链轮
Chain 链条
Chain 链条
Chamfering machine 倒角机
Change gate location to alter flow pattern改变水口位置进度而改变流线槽
Change gate location 改变浇口位置
Change screw speed 更改螺旋杆转速
Check for contamination 检查是否被污染
check for heater malfunction 检查炮筒温度是否正常
Check gated for proper location and adequate size 检查水口位置和尺寸
Check hopper and feed zone for contamination 检查塑料是否被污染
Check mold for undercuts and insufficient draft 检查模具的倒扣/拔模斜度不足
Check mold knockout mechanism for proper design and operation 检查模具的顶出系统
及功能
Check resin lubricant level 检查模具的润滑
Check resin lubricate level 检查模具的润滑
check the material for contamination 检查胶料是否被污染
Chrome plating 电镀铬
Chrome plating 电镀铬
Chrome 镀洛
Clamp/jig 夹具
Clean vents 清洁排气
Cloth polishing 脱模抛光
CMM 三次元
CNC grinding lathe 电脑外圆磨床
CNC machines 电脑锣
Cold slag well 冷料井
Collapsible core action “retreat” 缩呵
Collapsible core 缩呵
Color different 色差
Color mismatch 杂色
Color sreaks 条纹
Control/sensor 控制器/感应器
Cooling tube 散热管
Copper electrode 电极
Core insert 后模镶件
Core pin 镶针
Core 后模
Corner radius转角半径
Cracking 破裂
Cracking, crazing 裂纹
Crazing 网状纹
Crub screw 无头螺丝
Customer’s drawing 客供图
Customs fine
Customs seals
Cut‐in‐solid cavity 前模原生留
Cut‐in‐solid
core 后模原生留
Cycle time 循环周期
Data grid 日期
Date code 日期
Date code 日期印
Datum 基准
DDP
DDU
Decrease amount of regrind used 减少水口料的使用比例
Decrease booster time 减少推进时间
Decrease booster time 减少推进时间
decrease booster time 减少推进时间
Decrease cylinder and nozzle temperature 降低料筒和唧嘴的温度
Decrease cylinder temperature 减少料筒温度
Decrease holding pressure 减少保压
Decrease injection hold 减少射胶保压
Decrease injection pressure 减少注塑压力
Decrease injection speed 降低射胶速度
Decrease mold cavity temperature 降低前模温度
decrease number or size of vents 增加排气或增大排气
Decrease overall cycle time 升高总周期
Delamination 剥离
Delamination/skinning 分层
Demolding polish 脱模抛光
Depth for the nozzle into the mold 唧嘴进入模具的深度
Depth guage 深度尺
Diameter of the location ring 法兰直径
Diameter 直径
Direct sprue on part 直接大水口到产品
Discoloration 混色
Discoloration 脱色
distance of mold opening 模具开模距离
Double action slider 二次行位
Double color molds 双色模
Dowel pin 管钉
Dowel pin 管钉
Draft angle 拔模角
Draft angle 出模角度
Drag marks 拖花
Drag marks 拖花
Drawback: duties payment
refunded because freight is re‐exported or for similar circumstances
Drill bit/ cutter sharpener 磨刀机
Drill bit/ cutter sharpener 磨刀机
Drill presses 钻床
Drop gate 点水口
Dry material 烘干料
Dry resin pellets before use 在使用前烘干料粒
ED piercing mill 细孔放电
Edge gate 边水口
Edge/side gate 边水口
EDM computer controlled 放电加工
EDM
finished 火花纹
EDM 放电加工
EGB(ejector guide bush) 中托司
Ejected mark 顶白
Ejecting system 顶出系统
Ejector bar 顶块
Ejector bushes 顶针套
Ejector marks 顶白
Ejector pin 顶针
Ejector plate 顶针板
Ejector retainer plate 顶针面板
Ejector retainer plate顶针板
Ejectors not returned 顶针不回
Electric leak 漏电
Electronic weigh scale 电子称
Engrave 雕刻
Engrave
刻字
Engraving 雕刻
Equalize/balance mold temperature of both halves 平衡模温
Excessive flash 大面积披锋
Excessive shrinkage 缩水
Export country 出口国家
Eye bolt 吊模孔
Fan gate 扇形水口
Fang ate 扇形浇口
Fillet/inside radius 圆角
Filling uneven 走胶不平衡
Fine texture 细纹
Fine thread 细螺纹
Finish cavities 前模的表面处理
Fitting machines 飞模机 一楼
Fixed location ringф 前法兰直径
Flash marks/burr 披锋
Flash 披锋
Flat head cap screw 平头螺丝
Flat
hex cap screw fhcs 平头螺丝
Floating core 浮板
Floating insert 弹块
Floating plate 浮板
Flow marks/ flow lines 流痕
Flow mark流纹
Flow, halo, blush marks 流纹，缩孔，黄斑
Flush 平凹
For food marking insert 食品级材料标示镶件
Full round 圆形
Galling 擦烧
Gas trapped 困气
Gate shear 胶口剪切
Gate type 入水口型
Gear rack 齿条
Gear wheel/ intermediate gear wheel 链轮
Gear 齿轮
Geles 结胶点
Gels/ clear spots 污点
Gib locating slot/dowel pin 管钉
Gib 行位压板
Graphite electrode 石墨电极
Grease/ oil stains 油污
Green die 防锈剂
Grooved ball bearing 滚珠轴承
Guage block 量块
Guide bushes 导套
Guide pin 导柱
Guide pin/leader pin 导柱
Guide/locating system 导向定位系统
Gun drill 深孔钻
Gussets/ rocket ribs 火箭骨
H mold H型模
Half round 半圆
Hard mold 硬模
Hardened 加硬
Hardness tester 硬度计
Hasco standard parts HASCO 标准零件
Heat treatment 热处理
Heater 加热器
Height guage 高度尺
Helical nut 蜗杆套
Helical spindle 蜗杆
Hex socket screw
无头螺丝
Hexagonal head screw 六角头螺丝
High polish 高抛光
Hoist ring 吊环
Holding plate for angle pin 斜导柱压块
Hole 孔
Hot manifold plate 热流道，分流道板
Hot runner brand/mark 热流道品牌
Hot runner pin gate 热流道点水口
Hot runner plate 热流道板
Hydraulic cylinder 油缸
Hydraulic cylinder 油缸
Hydraulic handjack 油压板车
Hydraulic motor 马达
Hydraulic motor 液压马达
Hydraulic motor 液压马达
Hydraulic slide action 油缸式行位
Hydraulic 液压式
I million or above 一百万或以上
I mold 工字模
Imitate DME 仿DME
Imitate hasco 仿HASCO
improve mold cavity venting 改进前模的排气
Inch standard parts 英制标准零件
Increase backpressure 增加背压
Increase clamp pressure 增大摸锁力
Increase clamp pressure 增加模锁力
Increase cold slug area in size
or number 增加冷却数量和尺寸
Increase cylinder temperature 升高料筒的温度
Increase gate size and change gate location 增大进浇口的尺寸/改变进胶位置
Increase holding time 延长保压时间
Increase injection hold 增加射胶保压
Increase melt and mold temperature 升高溶胶温度或模温
Increase melt temperature 增加溶胶温度
Increase mold close 增加合模时间
Increase mold cooling time 延长模具冷却时间
Increase nozzle temperature 升高唧嘴的温度
Increase overall cycle time 减少总周期
Increase plasticating capacity of machine or use machine with large
plasticating capacity 增大搅
拌机的功率或使用增塑能力大的设备
Increase screw speed 增大螺杆速度
Increase shot length 增加溶胶注射行程
Increase shot size and confirm cushion 增大料嘴尺寸并确认衬垫
Increase the size of the gate 加大水口位置
Injection defects 注塑瑕疵
injection machine drawing 注塑机图纸
Injection molding machine 注塑机
Inner diameter 内径
Insert overmolded 放镶件
Inside radius 内转角
Insulating plate 隔热板
insure regrind
is not too coarse 确保料粒不要太大
Jetting 射纹
Jetting/snake flow 蛇流
Jiffy plugs 厚唨
Key 键
Kiss off 碰穿
Kiss‐off 枕位碰穿
Knock out hole 顶棍孔
KO hole distance KO孔间距
KO insert 顶棍孔镶件
ko screw type KO孔镶件
Large insert with cooling lines 铍铜
Latch 插销
Lathe CNC 电脑车床
Lathe manual
车床
Lens/dimple 波子
Lifter base 斜顶座
Lifter eye bolt 吊环
Lifter guide block 斜顶导向块
Limit screw 限位螺丝
Limit switch 限位开关
Limit switch 行程开关
Linear/wire cutting machine 线割机
Lkm inch dimension LKM英制尺寸
Locating ring 法兰
Magnet 500 kg 磁力座
make sure mold is vented correctly and vents are clear 确保排气正确和清洁
Make sure part contains no sharp variation in cross sections 确保零件没有尖锐的
变化
Manual grinding machine 磨床
Mechanical slide action 机械式行位
Mechanism 机械式
Medium polish 中抛光
Medium polish/demolding polish 中抛光
Metric 公制
Micrometer 千分尺
Milling machine
manual 铣床
Mirror polish 镜面抛光
Mirror polish 镜面抛光
Mismatch 段差
Missing part 漏件
Modify injection speed 改变射胶速度
Mold base 模胚
Mold base 模胚
Mold counter 计数器
Mold design 模具设计
Mold drawing 模图
mold fitting dimension 模具安装于注塑机上的尺寸
Mold frame 模架
Mold leg 模脚
Mold material 注塑产品材料
Mold number 模具编号
Mold opening distance
开模距离
Mold thickness 模具厚度
Mold warranty 模具寿命
Mould unit 模具
Move mode to smaller shot‐size press 把模具安装在注射量较小的注塑机上
Movement limiting shoulder bolt 塞打螺丝/限位螺丝
Movement 运动
Moving location ring ф 后法兰直径
Name plate 铭牌
Name plate 铭牌
Needle bearing 针式轴承
Nitrited 氮化
No cavity number 无模腔编号
No ejector hole tapped 顶棍板无牙
Non‐fraudulent violation of the regulation
Nozzle injection hole diameter 唧嘴注射孔直径
Nozzle radius 唧嘴半径
Oil manifold 集油器
Open the gates 打开水口
Optical polish 光学抛光
Optical/mirror polish 镜面抛光
Original DME 原装DME
Original hasco 原装 hasco
O‐ring 密封圈
Outer diameter 外径
Outside radius 外转角
Outside radius 外转角
Overhead block & tackle
天车
Oversize part 零件超差
Oversized parts 产品尺寸过大
P20/1.2311
Parsetter 红外线对导仪
Part drawing 产品图
Part name 产品名称
Part no. 产品编号
Part sticking 粘零件
Part sticking 产品粘前模
Parting line 分型面
Parting lock 树脂开闭器（尼龙扣
Pilferage
Pin guage 针规
Pin point gate 细水口
Plastic injection machines 注塑机
Plastic material 胶料
Plastic thickness 胶厚
Plastic 胶位
Plate travelling/ mold misalignment 模板移动
Plugs 侯塞
Pneumatic motor 气缸
Polishing 省模（抛光）
Polymer degredation 树脂降解
Pre‐hardened steel 预硬钢
Prehardened 预加热
Press block 挤紧块
Press block 模料挤紧块
Probe 探针
Projector 投影仪
provide additional mold vents 在模具上增加排气
Provide additional vents in mold 予设补充排气
Pry bar slot 翘模坑
Pry bar slots 开模槽
Puller bolt 水口扣针
Puller lock latch lock 拉钩
Puller 拉钩
Punch 打孔机
Purchase order 订单
Purge heating cylinder 清洗加热料筒
purge or clean the screw and barrel 清洁/清洗螺杆，料缸
Quotas quantity of one HTS item allowed to be
imported at either higher or lower rate of duties
Rack 齿条
Radial 圆角
Radius 半径
Raised out凸出
Recess 凹入
Recycling markings 回收标记
Reference EDM N° 参考EDM N°
Reference texture N°参考蚀纹N°
relocate gate 改变进胶点
Relocate gates on or as near as possible to thick sections 尽可能将水口位置移到较厚的胶位
Removable cavity
镶前模
Removable core 镶后模
Resin marking insert 材料标示镶件
Retraction spring 复位弹簧
Return pin 回针
Rev. ejection 前模顶出
RFQ only 仅供报价
Rib 骨位
Rib 骨位/加强筋
Ring gate 环形浇口
Ring gate 环形水口
Ring spacer 间隙圈
Roller bearings 滚珠轴承
Rough texture 粗纹
Rough thread 粗螺纹
Runner lock pin 水口扣针
Runner plate 水口板
Runner shut off 流道开关
S50C/1.1730
Safety lock 安全锁
Safety strap 摸锁
Sand polish 喷沙
Sandwitch mold 汉堡模
Scratch 刮伤
Scratches 刮花
Screw 螺丝
Sensor感应器
Servo motor 伺服马达
Set screw 固定螺丝
Shaft key 键
Sharp corner 尖角
Sharp edge 尖边
Short shot 短射
Short shot 进料不足
Short shot/ non‐fill/ short mold 走水不齐
Short slots 短胶
Shorten overall cycle 缩短总的周期
Shoulder screw 限位螺丝（带肩螺丝，塞打螺丝
Shrinkage rate 缩水率
Shrinkage 缩水率
Shut off 擦穿位
Side lock 边锁
Sink mark 缩水
Sink marks 缩水痕
Sino mold tooling specification 模具明细表
Sino standard sino 标准
Sintering vents 排气钢
Sleeve 司筒
Slide base 行位
Slide cut‐in‐solid 行位原生留
Slide guide block 行位导向块
Slide guide plate 行位导向块
Slide insert 行位镶件
Slide insert 行位镶件
Slide lock 行位锁
/行位扣
Slide not returned 行位不回
Slide retainer 行位扣
Slide wear plate 行位垫板
Slide wear plate 行位耐磨块
Slide 行位
Small grinding machines 小碎磨
Socket head cap screw 杯头螺丝
Socket head sounter sunk screws 平头螺丝
Soft mold 软模
Solid work
Spacer plate 方铁
Spacer ring/washer 间隙圈
Splay marks, silver streaks, splash marks扩张痕，银丝，飞溅痕
Splay/ splash mark/ silver streaks 银纹
Split mold/ expandible cavity 双并式模具
Spring 弹簧
Sprue bush radius 唧嘴球半径
Sprue bushing 唧嘴
Sprue lock pin 拉料杆
Sprue puller pin 拉杆
Sprue sticking 粘主流道
Sprue sticking 挂水口
Sprue/gate 浇口
SRP bushing 直导套
Standard 标准
Step 断差，台阶
Stepped
ejector pin 有托顶针
Sticking cavity 粘前模
Sticking cavity 粘前模
Sticking core 粘后模
Sticking core 粘后模
Sticking core/ hanged runner 粘水口
Stone polish 油石抛光
Stop block 限位块
Stop pin 垃圾钉
Straight side interlocks T型锁
Straight side interlocks 直身辅助器
Stress crack 应力电裂
Stress mark 拉伤
Stringiness stringing 眼线
Stripper plate bushing 直导套
Stripper plate 推板
Stripper plate 推板
Stripper screw脱料螺丝
Stripper/sleeve 推板/司筒
Sub gate in ejection 潜水口到顶针
Sub gate in part 潜水口到产品
Sub gate 潜水口
Suck back 倒流
Supplied by customer 客供
Supplied by sino mold sino自供
Support pillar 撑头
Support pin 边钉
Support plate 支撑板
Surface finish (low gloss) 表面质量（不光亮）
Surface finish 表面处理
Surface treatment 表面处理
T mold T型模
T wedge block/swallow tail 铲基
Tap & die hand held 攻牙
Tap & die pneumatic 气动攻牙机
Tapered interlocks 斜度辅助器
Tapered interlocks 斜度辅助器
Tapered interlocks 斜度锁
Texture 蚀纹
Texturing 蚀纹
Thermocouple connector 接线盒
Thermocouple 电热偶
Through hardened steel 全硬钢
Through hardened 加硬
tie bar diameter
and distance Tie bar 的尺寸和距离
Tie bar distance tie bar距离
To be liable for a penny of
To expedite the clearance
To file certifications with customs
To follow the current
Tolerant part 公差部分
Tool microscope 显微镜
Top clamping plate 面板
Trapezoid 梯形
Trapped gas 困气
Try increasing and decreasing injection pressure 尝试升高和降低射胶压力
Tunnel gate 隧道水口
Two‐stage ejector 二次顶出
Type of mold 模具类型
type(tonnage) 类型（吨位）
Undercut 倒扣
Undersized parts 产品尺寸过小
Undersized parts 零件尺寸不足
Uneven filling 走水不平衡
Unfilled plastic 缺胶
Unscrewing mold 螺纹模
Unscrewing 脱螺纹
Unscrewing 自动脱螺纹
Use high compression screw 使用高压螺杆
Valve gate 热流道针阀式水口
Valve gate 针阀式水口
Venier calipers 游标卡尺
Vent cavity in the weld area 在夹接区域加排气
Venting groove 排气
Venting pin 排气针
Venting slots 排气槽
Venting system 排气系统
Video measurement system 二次元
Vise 虎钳
Voids 进胶不满
Voids 缩孔
W.B wear plate 铲基耐磨块
Wall thickness 胶位厚度
Warpage 翘曲，变形
Warpage/deformation 变形
Warping, part distortion 零件扭曲，变形
Water leak 漏水
Water lines connector type 运水接头类型
Waterline not marked 无运水字麦
Wear plates 耐磨板
Wedge block 铲机
Wedge wear
plate 铲机耐磨块
Wedge/heel block 铲基
Weld line 熔接线
Weld lines 夹水线
Weld/ meld/ transfer/ knit line 熔接线
Wheel bearing/tapered roller bearing 轴承
White mark 白化
Wrong part 错件
X style straight side interlocks 双头直身辅助器
发布评论