2023年12月7日发(作者：)
RS/6000液晶显示屏上显示代码(LED)的含义
本文介绍RS/6000启动过程中机器上的液晶显示屏代码的含义。本文代码不针对具体机型。
---------- Dump Progress Indicator ----------
0c0
The dump completed successfully
0c1
The dump failed due to an I/O error.
0c2
A user-requested dump has started. You requested a dump using the SYSDUMPSTART command,
a dump key sequence, or the Reset button.
0c3
The dump is inhibit
0c4
The dump did not complete. A partial dump was written to the dump device. There is not enough
space on the dump deviceto contain the entire dump. To prevent this problem from occuring again,
you must increase the size of your dumpmedia.
0c5 The dump failed to start. An unecpected error occured while the system was attempting to write to
the dump media.
0c6 A dump to the secondary dump device was requested. Make the secondary dump device ready, then
press CTRL-ALT-NUMPAD2.
0c7
Reserved.
0c8
The dump function is disabled. No primary dump device is configured.
0c9
A dump is in progress.
0cc
Unknown dump failure
---------- Diagnostics Load Progress Indicators -----------
c00
AIX Install/Maintenance loaded successfully.
c01
Insert the first diagnostic diskette.
c02
Diskettes inserted out of sequence.
c03
The wrong diskette is in the drive.
c04
The loading stopped with an irrecoverable error.
c05
A diskette error occurred.
c08
RAM filesystem started incorrectly.
c07
Insert the next diagnostic diskette.
c09
The diskette drive is reading or writing a diskette.
c20
An unexpected halt occured, and the system is configured to enter the kernel debug program instead
of entering asystem dump.
c21
The 'ifconfig' command was unable to configure the network for the client network host.
c22 The 'tftp' command was unable to read client's file during a client network
boot.
c24
Unable to read client's file during a client network boot.
c25
Client did not mount remote miniroot during network install.
c26
Client did not mount the /usr filesystem during the network boot.
c29
System was unable to configure the network device.
c31 Select the console display for the diagnostics. To select "No console display", set the key mode
switch to normal thento Service. The diagnostic program will then load and run the diagnostics
automatically.
c32
A direct-attached display (HFT) was selected.
c33
a TTY terminal attached to serial ports S1 or S2 was selected.
c34
A file was selected. The console messages store in a file
c40
Configuration files are been restored.
c41
Could not determine the boot type or device.
c42
Extracting data files from diskette.
c43
Diagboot cannot be accessed.
c44
Initialyzing installation database with target disk information.
c45
Cannot configure the console.
c46
Normal installation processing.
c47
Could not create a physical volume identifier (PVID) on disk.
c48
Prompting you for input.
c49
Could not create or form the JFS log.
c50
Creating rootvg volume group on target disk
c51
No paging space were found.
c52
Changing from RAM environment to disk environment.
c53
Not enough space in the /tmp directory to do a preservation installation.
c54
Installing either BOS or additionnal packages.
c55
Could not remove the specified logical volume in a preservation installation.
c56
Running user-defined customization.
c57
Failure to restore BOS.
c58
Display message to turn the key.
c59 Could not copy either device special files, device ODM, or volume group information from RAM to
disk.
c61
Failed to create the boot image.
c70
Problem Mounting diagnostics CDROM disc.
c99
Diagnostics have completed. This code is only used when there is no console.
--------Debugger Progress Indicators ----------
c20 Kernel debug program activated. An unexpected system halt has occured, and you have configured
the system
to enter the kernel debug program instead of performing a dump.
---------Built-In Self Test (Bist) Indicators---------
100
BIST completed successfully. Control was passed to IPL ROS.
101
BIST started following RESET
102
BIST started following Power-on Reset
103
BIST could not determine the system model number.
104
Equipment conflict. BIST could not find the CBA.
105
BIST could not read the OCS EPROM.
106
BIST detected a module error.
111
OCS stopped. BIST detected a module error.
112
A checkstop occured during BIST.
113
BIST checkstop count is greater than 1.
120
BIST starting a CRC check on the 8752 EPROM.
121
BIST detected a bad CRC in the first 32K of the OCS EPROM.
122
BIST started a CRC check on the first 32K of the OCS EPROM.
123
BIST detected a bad CRC on the OCS area of NVRAM.
124
BIST started a CRC check on the OCS area of NVRAM.
125
BIST detected a bad CRC on the time-of-day area of NVRAM.
126
BIST started a CRC check on the time-of-day area of the NVRAM.
127
BIST detected a bad CRC on the 8752 EPROM.
130
BIST presence test started.
140
BIST failed: procedure error
142
BIST failed: procedure error
143
Invalid memory configuration.
144
BIST failed; procedure error.
151
BIST started AIPGM test code.
152
BIST started DCLST test code.
153
BIST started ACLST test code.
154
BIST started AST test code.
160
Bad EPOW Signal/Power status signal
161
BIST being conducted on BUMP I/O
162
BIST being conducted on JTAG
163
BIST being conducted on Direct I/O
164
BIST being conducted on CPU
165
BIST being conducted on DCB and Memory
166
BIST being conducted on interrupts
170
BIST being conducted on 'Multi-Processor
180
BIST logout failed.
182
BIST COP bus not responding
185
A checkstop condition occured during the BIST
186
System logic-generated checkstop (Model 250 only)
187
Graphics-generated checkstop (Model 250)
195
BIST logout completed.
888
BIST did not start
200
IPL attempted with keylock in the SECURE position.
201
IPL ROM test failed or checkstop occured (irrecoverable)
202
IPL ROM test failed or checkstop occured (irrecoverable)
203
Unexpected data storage interrupt.
204
Unexpected instruction storage interrupt.
205
Unexpected external interrupt.
206
Unexpected alignment interrupt.
207
Unexpected program interrupt.
208
Unexpected floating point unavailable interrupt.
209
Unexpected SVC interrupt.
20c
L2 cache POST error. (The display shows a solid 20c for 5 seconds
------- Power-On Self Test -------
210
Unexpected SVC interrupt.
211
IPL ROM CRC comparison error (irrecoverable).
212
RAM POST memory configuration error or no memory found (irrecoverable).
213
RAM POST failure (irrecoverable).
214
Power status register failed (irrecoverable).
215
A low voltage condition is present (irrecoverable).
216
IPL ROM code being uncompressed into memory.
217
End of bootlist encountered.
218
RAM POST is looking for 1M bytes of good memory.
219
RAM POST bit map is being generated.
21c
L2 cache is not detected. (The display shows a solid 21c for 5 sec)
220
IPL control block is being initialized.
221
NVRAM CRC comparison error during AIX.
IPL(Key Mode Switch in Normal mode).
Reset NVRAM by reaccomplishing IPL in Service mode. For systems with an internal, direct-bus-attached(DBA)disk,IPL
ROM attempted to perform an IPL from that disk before halting with this three-digit display value.
222 Attempting a Normal mode IPL from Standard I/O planar attached devices specified in NVRAM
IPL Devices List.
223 Attempting a Normal mode IPL from SCSI attached devices specified in NVRAM IPL Devices
List.
Note: May be caused by incorrect jumper setting for external SCSI devices or by incorrect SCSI
terminator.
REFER FFC B88
224
Attempting a Normal mode restart from 9333 subsystem device specified in NVRAM device list.
225 Attempting a Normal mode IPL from IBM 7012 DBA disk attached devices specified in NVRAM
IPL Devices List.
226
Attempting a Normal mode restart from Ethernet specified in NVRAM device list.
227
Attempting a Normal mode restart from Token Ring specified in NVRAM device list.
228
Attempting a Normal mode IPL from NVRAM expansion code.
229 Attempting a Normal mode IPL from NVRAM IPL Devices List; cannot IPL from any of the listed
devices, or there are
no valid entry in the Devices List.
22c
Attempting a normal mode IPL from FDDI specified in NVRAM IPL device list.
230
Attempting a Normal mode restart from adapter feature ROM specified in IPL ROM devices list.
231
Attempting a Normal mode restart from Ethernet specified in IPL ROM devices list.
232 Attempting a Normal mode IPL from Standard I/O planar attached devices specified in Rom
Default Device List.
233 Attempting a Normal mode IPL from SCSI attached devices specified in IPL ROM Default Device
List.
234
Attempting a Normal mode restart from 9333 subsystem device specified in IPL ROM device list.
235 Attempting a Normal mode IPL from IBM 7012 DBA disk attached devices specified in IPL ROM
Default Device List.
236
Attempting a Normal mode restart from Ethernet specified in IPL ROM default devices list.
237
Attempting a Normal mode restart from Token Ring specified in IPL ROM default device list.
238
Attempting a Normal mode restart from Token Ring specified by the operator.
239
System failed to restart from the device chosen by the operator.
23c
Attempting a normal mode IPL from FDDI specified in IPL ROM device list.
240
Attempting a Service mode restart from adapter feature ROM.
241
Attempting a Normal mode IPL from devices specified in the NVRAM IPL Devices List. 242 Attempting a Service mode IPL from Standard I/O planar attached devices specified in NVRAM
IPL Devices List.
243 Attempting a Service mode IPL from SCSI attached devices specified in NVRAM IPL Devices
List.
244
Attempting a Service mode restart from 9333 subsystem device specified in NVRAM device list.
245 Attempting a Service mode IPL from IBM 7012 DBA disk attached devices specified in NVRAM
IPL Devices List.
246
Attempting a Service mode restart from Ethernet specified in NVRAM device list.
247
Attempting a Service mode restart from Token Ring specified in NVRAM device list.
248
Attempting a Service mode IPL from NVRAM expansion code.
249
Attempting a Service mode IPL from NVRAM IPL Devices List; cannot IPL from any of the listed
devices, or there areno valid entries in the Devices List.
24c
Attempting a service mode IPL from FDDI specified in NVRAM IPL device list.
250
Attempting a Service mode restart from adapter feature ROM specified in IPL ROM device list.
251
Attempting a Service mode restart from Ethernet specified in IPL ROM device list.
252 Attempting a Service mode IPL from standard I/O planar attached devicesspecified in ROM Default
Device List.
253 Attempting a Service mode IPL from SCSI attached devices specified in IPL ROM Default Device
List.
254
Attempting a Service mode restart from 9333 subsystem device specified in IPL ROM device list.
255 Attempting a Service mode IPL from IBM 7012 DBA disk'attached devices specified in IPL ROM
Default Devices List.
256
Attempting a Service mode restart from Ethernet specified in IPL ROM default device list.
257
Attempting a Service mode restart from Token Ring specified in IPL ROM default device list.
258
Attempting a Service mode restart from Token Ring specified by the operator.
259
Attempting a Service mode restart from FDDI specified by the operator.
25c
Attempting a normal mode IPL from FDDI specified in IPL ROM device list.
260
Information is being displayed on the display console.
261 Information will be displayed on the tty terminal when the "1" key is pressed on the tty terminal
keyboard.
262
A keyboard was not detected as being connected to the system's
NOTE: Check for blown planar fuses or for a corrupted boot on disk drive
263
Attempting a Normal mode restart from adapter feature ROM specified in NVRAM device list.
269
Stalled state - the system is unable to IPL
271
Mouse port POST.
272
Tablet port POST.
277
Auto Token-Ring LANstreamer MC 32 Adapter
278
Video ROM Scan POST.
279
FDDI adapter POST.
280
3COM Ethernet POST.
281
Keyboard POST executing.
282
Parallel port POST executing
283
Serial port POST executing
284
POWER Gt1 graphadapte POST executing
285
POWER Gt3 graphadapte POST executing
286
Token Ring adapter POST executing.
287
Ethernet adapter POST executing.
288
Adapter card slots being queried.
289
GTO POST.
290
IOCC POST error (irrecoverable).
291
Standard I/O POST running.
292
SCSI POST running.
293
IBM 7012 DBA disk POST running.
294
IOCC bad TCW SIMM in slot location J being tested.
295
Graphics Display adapter POST, color or grayscale.
296
ROM scan POST.
297
System model number does not compare between OCS and ROS
(irrecoverable). Attempting a software IPL.
298
Attempting a software IPL (warm boot).
299
IPL ROM passed control to the loaded program code.
301
Flash Utility ROM failed or checkstop occured (irrecoverable)
302
Flash Utility ROM failed or checkstop occured (irrecoverable)
302 Flash Utility ROM: User prompt, move the key to the service in order to perform an optional Flash
Update. LED
will only appear if the key switch is in the SECURE position. This signals the user that a Flash
Update may be
initiated by moving the key switch to the SERVICE position. If the key is moved to the SERVICE
position,
LED 303 will be displayed. This signals the user to press the reset button and select optional Flash
Update.
303 Flash Utility ROM: User prompt, press the reset button in order to perform an optional Flash
Update. LED
only appear if the key switch is in the SECURE position. This signals the user that a Flash Update
may be initiated
by moving the key switch to the SERVICE position. If the key is moved to the SERVICE position,
LED 303 will be
displayed. This signals the user to press the reset button and select optional Flash Update.
304
Flash Utility ROM IOCC POST error (irrecoverable)
305
Flash Utility ROM standard I/O POST running.
306
Flash Utility ROM is attempting IPL from Flash Update Boot Image.
307 Flash Utility ROM system model number does not compare between OCS and ROM
(irrecoverable).
308
Flash Utility ROM: IOCC TCW memory is being tested.
309
Flash Utility ROM passed control to a Flash Update Boot Image.
311
Flash Utility ROM CRC comparison error (irrecoverable).
312
Flash Utility ROM RAM POST memory configuration error or no memory found ( iirecoverable).
313
Flash Utility ROM RAM POST failure( irrecoverable).
314
Flash Utility ROM Power status register failed (irrecoverable).
315
Flash Utility ROM detected a low voltage condition.
318
Flash Utility ROM RAM POST is looking for good memory.
319
Flash Utility ROM RAM POST bit map is being generated.
322
CRC error on media Flash Image. No Flash Update performed.
323
Current Flash Image is being erased.
324
CRC error on new Flash Image after Update was performed. (Flash Image is corrupted).
325
Flash Image successful and complete.
500
Querying Native I/O slot.
501
Querying card in Slot 1
502
Querying card in Slot 2
503
Querying card in Slot 3
504
Querying card in Slot 4
505
Querying card in Slot 5
506
Querying card in Slot 6
507
Querying card in Slot 7
508
Querying card in Slot 8
510
Starting device configuration.
511
Device configuration completed.
512
Restoring device configuration files from media.
513
Restoring basic operating system installation files from media.
516
Contacting server during network boot
517
Mounting client remote file system during network IPL.
518
Remote mount of the root and /usr filesystems failed during network boot.
520
Bus configuration running.
521
/etc/init invoked cfgmgr with invalid options; /etc/init has been corrupted or incorrectly modified
(irrecoverable error).
522
The configuration manager has been invoked with conflicting options (irrecoverable error).
523
The configuration manager is unable to access the ODM database (irrecoverable error).
524 The configuration manager is unable to access the config rules object in the ODM database
(irrecoverable error).
525 The configuration manager is unable to get data from a customized device object in the ODM
database
(irrecoverable error).
526 The configuration manager is unable to get data from a customized device driver objet in the ODM
database
(irrecoverable error).
527 The configuration manager was invoked with the phase 1 flag; running phase 1 flag; running phase
1 at this point
is not permitted (irrecoverable error).
528 The configuration manager cannot find sequence rule, or no program was specified in the ODM
database
(irrecoverable error).
529
The configuration manager is unable to update ODM data
(irrecoverable error).
530
The program "savebase" returned an error.
531
The configuration manager is unable to access PdAt object class
(irrecoverable eroor)
532
There is not enough memory to continue (malloc failure);
irrecoverable error.
533
The configuration manager could not find a configure method for a device.
534
The configuration manager is unable to aquire database lock. irrecoverable error.
536
The configuration manager encountered more than one sequence rule specified
in the same phase. (irrecoverable error).
537
The configuration manager encountered an error when invoking the program in the sequence rule.
538
The configuration manager is going to invoke a configuration
539
The configuration method has terminated, and control has returned to the configuration manager. 551
IPL Varyon is running
552
IPL Varyon failed.
553
IPL phase 1 is complete. //有问题，/etc/initab 损坏
554
Unable to define NFS swap device during network boot
555
Unable to define NFS swap device during network boot
556
Logical Volume Manager encountered error during IPL varyon.
557
The root filesystem will not mount.
558
There is not enough memory to continue the IPL.
559
Less than 2MB of good memory are available to load the AIX kernel.
570
Virtual SCSI devices being configured.
571
HIPPI common function device driver being configured.
572
HIPPI IPI-3 master transport driver being configured.
573
HIPPI IPI-3 slave transport driver being configured.
574
HIPPI IPI-3 transport services user interface device driver being configured.
576
Generic async device driver being configured.
577
Generic SCSI device driver being configured.
578
Generic commo device driver being configured.
579
Device driver being configured for a generic device.
580
HIPPI TCPIP network interface driver being configured.
581
Configuring TCP/IP.
582
Configuring token ring data link control.
583
Configuring an Ethernet data link control.
584
Configuring an IEEE ethernet data link control.
585
Configuring an SDLC MPQP data link control.
586
Configuring a QLLC X.25 data link control.
587
Configuring NETBIOS.
588
Configuring a Bisync Read-Write (BSCRW).
589
SCSI target mode device being configured.
590
Diskless remote paging device being configured.
591
Configuring an LVM device driver
592
Configuring an HFT device driver
593
Configuring SNA device drivers.
594
Asynchronous I/O being defined or configured.
595
X.31 pseudo device being configured.
596
SNA DLC/LAPE pseudo device being configured.
597
OCS software being configured.
598
OCS hosts being configured during system reboot.
599
Configuring FDDI data link control.
5c0
Streams-based hardware drive being configured.
5c1
Streams-based X.25 protocol being configured.
5c2
Streams-based X.25 COMIO emulator driver being configured.
5c3
Streams-based X.25 TCP/IP interface driver being configured.
5c4
FCS adapter device driver being configured.
5c5
SCB network device driver for FCS is being configured.
5c6
AIX SNA channel being configured.
600
Starting network boot portion of /sbin/
602
Configuring network parent devices.
603
/usr/lib/methods/defsys
/usr/lib/methods/cggsys, or
/usr/lib/methods/cggbus failed.
604
Configuring physical network boot device.
605
Configuring physical network boot device failed.
606
Running /usr/sbin/ifconfig on logical network boot device.
607
/usr/sbin/ifconfig failed.
608 Attempting to retrieve the file with tftp. Note that a flashing 608 indicates multiple
attempts
to retrieve the client_info file are occuring.
609
The file does not exist or it is zero length.
610
Attempting remote mount of NFS file system
611
Remote mount of the NFS filesystem failed.
612
Accessing remote files; unconfiguring network boot device.
614
Configuring local paging devices.
615
Configuring of a local paging device failed.
616
Converting from diskette to dataless configuration.
617
Diskless to dataless configuration failed.
618
Configuring remote (NFS) paging devices.
619
Configuration of a remote (NFS) paging device failed.
620 Updating special device files and ODM in permanent filesystem with data from boot RAM
filesystem.
622
Boot process configuring for operating system installation.
650
IBM SCSD disk drive drive being configured
700
Progress indicator. A 1.1GB 8-bit SCSI disk drive being identified or configured.
701
Progress indicator. A 1.1GB 16-bit SCSI SE disk drive being identified or configured.
702
Progress indicator. A 1.1GB 16-bit SCSI differential disk drive being identified or configured.
703
Progress indicator. A 2.2GB 8-bit SCSI disk drive being identified or configured.
704
Progress indicator. A 2.2GB 16-bit SCSI SE disk drive being identified or configured.
705
The configuration method for the 2.2GB 16-bit differential SCSI disk drive is being run. If a
irrecoverableerror occurs, the system halts. identified or configured.
706
Progress indicator. A 4.5GB 16-bit SE SCSI disk drive is being identified or configured.
707
Progress indicator. A 4.5GB 16-bit differential SCSI drive is being identified or configured.
708
Progress indicator: A L2 cache is being identified or configured.
710
POWER GXT150M graphics adapterbeing ientifyied or configured.
711
Unknown adapter being identified or configured.
712
Graphics slot bus configuration is executing.
713
The IBM ARTIC960 device is being configured.
714
A video capture adapter is being configured.
715
The Ultimedia Services audio adapter is being configured. This LED displays briefly on the panel.
720
Unknown read/write optical drive type being configured.
721
Unknown disk or SCSI device being identified or configured.
722
Unknown disk being identified or configured.
723
Unknown CDROM being identified or configured.
724
Unknown tape drive being identified or configured.
725
Unknown display being identified or configured.
726
Unknown input device being idenor configured
727
Unknown adync device being idenor configured
发布评论